Brother HL-600 Series User Manual Download Page 57

Page: 57 / 84

CHAPTER 6 TROUBLESHOOTING

6–1

CHAPTER 6
TROUBLESHOOTING

ALARM INDICATIONS AT A GLANCE

Operator Calls

If an error occurs, the printer indicates an ‘operator call’ by blinking the
ALARM lamp and any of the following lamps.

Find the error and take the proper action to correct it. The printer
automatically recovers from most errors, but you may need to reset the
printer with the switches as described below.

Blinking Lamp

Error

Action

PAPER

❍↔●

ALARM

❍↔●

Paper jam

Paper empty

Mis Feed

Clear the paper jam referring
to the next section “PAPER
JAMS” and press the
FF/CONT switch if the printer
does not automatically resume
printing.

Load paper in the printer
referring to Chapter 2 and
press the FF/CONT switch.

Reinstall the paper and press
the FF/CONT switch.

COVER

❍↔●

ALARM

❍↔●

Cover open

Close the top cover of the
printer or install the multi-
purpose sheet feeder into the
printer firmly.

TONER

❍↔●

ALARM

❍↔●

( every 5 seconds)

TONER

❍↔●

ALARM

●↔●

Toner low

Toner Empty

Indicates that the printer has
approximately 100 pages of
printing left before the toner
cartridge is empty.

Replace the toner cartridge
with a new one.

Summary of Contents for HL-600 Series





















































































Search results

Summary of Contents for HL-600 Series

Reviews:

Related manuals for HL-600 Series

Brands by name

Popular brands

Brother HL-600 Series, User Manual

Search results

Summary of Contents for HL-600 Series

Reviews:

Related manuals for HL-600 Series

Brands by name

Popular brands