Brother DR-210 Series Remanufacturing Instructions Download Page 11

Page: 11 / 21

SSS

™

1127 |

Visit Static Control

on the web @ www.scc-inc.com

SSS

™

1127

STEP 3.8

STEP 3.7

STEP 3.9

Place the drive side end cap onto the cartridge and ensure that

the drive side support bearing tabs are on the outer part of the

drive side end plate (Figure 3.9).

Place the contact side developer roller support spring and

bearing onto the developer roller axle (Figure 3.8).

Place the contact side end cap and secure with a screw

(Figures 3.7A and 3.7B).

FIGURE 3.8

FIGURE 3.7B

FIGURE 3.7A

FIGURE 3.9

ASSEMBLING THE CARTRIDGE

Note:

Reference Figures 4.1A and 4.1B on page 13

under the “Resetting the Flag Gear” section, to
ensure the flag gear tab is in the reset location
prior to placing the drive side end cap onto the
cartridge. Print error failures could result if the
gear is not set properly.

Screw

Drive Side Support Bearing Tabs

Contact Side

Developer Roller

Support Bearing

STEP 3.10

Use a small slotted screwdriver to gently set the foam under

the drive side developer roller support bearing back into place

(Figures 3.10A and 3.10B).

FIGURE 3.10A

FIGURE 3.10B

efore

fter

Foam

No Foam

Contact

Side End

Cap

Summary of Contents for DR-210 Series






















Search results

Summary of Contents for DR-210 Series

Reviews:

Related manuals for DR-210 Series

Brands by name

Popular brands

Brother DR-210 Series, Remanufacturing Instructions

Search results

Summary of Contents for DR-210 Series

Reviews:

Related manuals for DR-210 Series

Brands by name

Popular brands