manualshive.com logo in svg

Brother DR-210 Series, Remanufacturing Instructions, Page: 6 / 21

Share
Download
Brother DR-210 Series Remanufacturing Instructions Download Page 6

SSS

™

 1127 |  

6

Visit Static Control

®

 on the web @ www.scc-inc.com

SSS

™

 1127

STEP 2.4

STEP 2.2

STEP 2.3

STEP 2.1

STEP 2.5

STEP 2.6

Remove the gears from the drive side of the cartridge in the order 

shown. Idler drive gear (1), agitator drive gear (2), idler gear (3), and 

the toner adder roller drive gear (4) (Figure 2.6).

Remove the cartridge drive gear (Figure 2.4) and check the 

boss for alignment. 

Use a small slotted screwdriver to release the locking tab on 

the underside of the drive side end plate (Figure 2.2).

Remove the flag gear spring and the flag gear (Figure 2.5).

Remove the drive side end plate (Figure 2.3).

On the drive side end plate, remove the two screws as shown 

in Figure 2.1.

FIGURE 2.4

FIGURE 2.3

FIGURE 2.2

FIGURE 2.1

FIGURE 2.6

FIGURE 2.5

DISASSEMBLING THE CARTRIDGE

Note: 

See warning on page 5.

Note: 

See warning on page 5.

3

4

2

1

Screws

Phillips 

Screwdriver

Small Slotted

Screwdriver

Remove Gear

Flag Gear

Spring

Flag Gear

Drive Side 

End Plate

Locking Tab

Summary of Contents for DR-210 Series






















Reviews:

No comments