Brother DR-210 Series Remanufacturing Instructions Download Page 19

Page: 19 / 21

SSS

™

1127 |

SSS

™

1127

Visit Static Control

on the web @ www.scc-inc.com

DRUM RESET INSTRUCTIONS

OPTIONAL

1. Press + or - to choose

Machine Info

. Press

2. Press + or - to choose

Reset Parts Life

Press

3. Press + to choose Drum Unit. Press

4. Press + or - to choose the drum color that

was replaced. Press

twice.

For Multi-Function Copiers (MFC) and

Digital Copier Printers (DCP)

1. Power the printer on.
2. Press

MENU, 6, 4

3. Press

and then press + or - to choose

the color cartridge that is installed.

Press

4. Press

to reset the drum unit counter.

5. Press

STOP / EXIT

For MFC 9120CN and 9125CN:

1. Power the printer on.
2. Press

MENU, 5, 6

3. Press

and then press + or - to choose

the color cartridge that is installed.

Press

4. Press

to reset the drum unit counter.

5. Press

STOP / EXIT

For MFC 9010CN and DCP 9010CN:

1. Power the printer on.
2. Press

MENU, 8, 4

3. Press

and then press + or - to choose

the color cartridge that is installed.

Press

4. Press

to reset the drum unit counter.

5. Press

STOP / EXIT

For 9320CW and 9325CW:

Drum Reset Instructions:

1. Power the printer on.
2. Press + or - to choose

Machine Info

Press

3. Press + or - to choose

Parts Life

Press

4. Press + to choose

Drum Life

Press

5. Press + or - to choose the

drum color that was replaced.

Press

twice.

Drum Reset Instruction (OPTION # 2):

Note:

Always reset the drum counter on a

Brother HL-3040/3075CN printer after

replacement. However, this reset may

be performed at any time. There are four

drum cartridges in a printer: black, cyan,

magenta and yellow. Each drum has its

own drum counter.

1. Power the printer on.
2. Press + or - to select

MACHINE INFO

...

3. Press

to proceed to the next menu.

4. Press + or - to choose

RESET PARTS LIFE

5. Press

and then press + or - to choose

DRUM UNIT

6. Press

and then press + or - to choose the

color cartridge that is installed.

7. Press

twice.

Drum Reset Instructions

Summary of Contents for DR-210 Series






















Search results

Summary of Contents for DR-210 Series

Reviews:

Related manuals for DR-210 Series

Brands by name

Popular brands

Brother DR-210 Series, Remanufacturing Instructions

Search results

Summary of Contents for DR-210 Series

Reviews:

Related manuals for DR-210 Series

Brands by name

Popular brands