background image

Flued Indoor Gas Heater - Instruction Manual

20

 July 2019 - V1

The  appliance  is  furnished  and  preset  for  the  gas

function (G 20) and regulated in factory.

Note: the apparatus can also be requested with the

GPL gas function.

First things to do before you start the appliance check:

- If the appliance is preset for the right gas

-  The  gas  connection  is  correctly  realized  and  the

gas switch is opened.

- The electrical connections are properly done.

Remember it is also important to realize a good

ground connection and to respect the neutral phase.

During the first start, could be emissions of

vapors and odors annoying non dangerous. To

avoid these inconveniences, it is recommended to

run the unit at full power for several hours and ven-

tilate the room.

For  greater  comfort  in  the  heated  environment,  we

advise  using  the  humidifier  tray  (1)  encased  in  the

casing.

Do  not  fill  the  tray  to  the  top  to  prevent

water  overflowing  with  consequent  damage

to or malfunction of the appliance.

Only fill the tray with water. Avoid all other

liquids that could damage the tray or cause

appliance malfunctions.

After performing all the preparation operations for ini-

tial start-up, to start the appliance:

- make sure the fuel tap is open;

- plug into the power supply socket;

- move the master switch (if fitted) to "on" or fit the

power plug in the wall socket;

- press the On/Off key (see User section) to switch

on the appliance;

- set the room thermostat  at a high value to reduce

heating time;

After startup, the appliance runs until it reaches the

set room temperature.

In case of malfunctions in startup procedure or ope-

ration,  the  appliance  STOPS  and  the  relevant

unblock  signal  lights  up  on  the  display.  Reset  the

appliance  by  keeping  the  unblock  button  pressed.

Wait until the startup procedure is completed and the

operation signal lights up.

-  When  the  appliance  is  running,  set  the  clock  and

the timer for automatic operation (see User section).

FIRST SERVICE START

PRELIMINARY OPERATIONS 

21

CUSTOMER SERVICE

Summary of Contents for 2620970

































Reviews: