manualshive.com logo in svg

Brocade Communications Systems ICX 7250 series, Configuration Manual

Share
Download
Brocade Communications Systems ICX 7250 series Configuration Manual Download Page 102

Setting the bandwidth value for a tunnel interface

The current bandwidth value for a tunnel interface can be set and communicated to higher-level protocols such as OSPF.

1. Enter the 

configure terminal

 command to access global configuration mode.

device# configure terminal

2. Enter the 

interface tunnel

 command and specify a value to configure a tunnel interface.

device(config)# interface tunnel 2

3. Enter the 

tunnel mode gre ip

 command to enable GRE IP encapsulation on the tunnel interface.

device(config-tnif-2)# tunnel mode gre ip

4. Enter the 

tunnel source

 command and specify an IP address to configure the source address for the tunnel interface.

device(config-tnif-2)# tunnel source 10.0.0.1

5. Enter the 

tunnel destination

 command and specify an IP address to configure the destination address for the tunnel interface.

device(config-tnif-2)# tunnel destination 10.10.0.1 

6. Enter the 

ip address

 command and specify an IP address and a network mask to assign an IP address to the tunnel interface.

device(config-tnif-2)# ip address 10.0.0.1/24

7. Enter the 

bandwidth

 command and specify a value to set the bandwidth value on the interface.

device(config-tnif-2)# bandwidth 2000

This example sets the bandwidth to 2000 kbps on a specific tunnel interface .

device# configure terminal

device(config)# interface tunnel 2

device(config-tnif-2)# tunnel mode gre ip

device(config-tnif-2)# tunnel source 10.0.0.1

device(config-tnif-2)# tunnel destination 10.10.0.1

device(config-tnif-2)# ip address 10.0.0.1/24

device(config-tnif-2)# bandwidth 2000

The bandwidth specified in this example results in the following OSPF interface costs, assuming the auto-cost is 100:

•

OSPF Interface Cost for the Trunk Group is equal to ((100 * 1000) + (2000 - 1)÷ 2000) = 50

•

OSPF Interface Cost for the GRE/IPv6 tunnel is equal to ((100 * 1000) + (2000 - 1)÷ 2000) = 50

User-configurable MAC address per IP interface

Manual configuration of one IP MAC address for each Layer 3 physical or virtual ethernet (VE) interface on a device is permitted. The
configured MAC address is used as the source MAC address by routing protocols or hardware communication related to the IPv4 or
IPv6 addresses on the interface, for example in ARP or neighbor discovery (ND) packets to the interface. The IPv4 and IPv6 addresses
use the same IP MAC address for any software and hardware communication.

If an IP MAC address is not configured, the IP interface uses the MAC address from the router or stack.

The user-configurable IP MAC address feature supports the following unicast protocols:

•

IPv4 support—ARP, BGP, OSPF, RIP

User-configurable MAC address per IP interface

Brocade FastIron Layer 3 Routing Configuration Guide

102

53-1003903-04

Summary of Contents for ICX 7250 series




































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands