manualshive.com logo in svg

Broadcom NetXtreme BCM57 Series, User Manual

Share
Download
Broadcom NetXtreme BCM57 Series User Manual Download Page 148

iSCSI Protocol and Broadcom Boot Agent Software

NetXtreme 

User Guide

 

Broadcom

®

 

April 2017 • 2CS57XX-CDUM514-R

Page 148

DHCP iSCSI Boot Configuration for IPv6

The DHCPv6 server can provide a number of options, including stateless or stateful IP configuration, as well s 
information to the DHCPv6 client. For iSCSI boot, Broadcom adapters support the following DHCP 
configurations:

•

DHCPv6 Option 16, Vendor Class Option

•

DHCPv6 Option 17, Vendor-Specific Information

DHCPv6 Option 16, Vendor Class Option

DHCPv6 Option 16 (vendor class option) must be present and must contain a string that matches your 
configured 

DHCP Vendor ID 

parameter. The 

DHCP Vendor ID

 value is BRCM ISAN, as shown in 

General 

Parameters

 of the iSCSI Boot Configuration menu.

The content of Option 16 should be <2-byte length> <DHCP Vendor ID>.

DHCPv6 Option 17, Vendor-Specific Information

DHCPv6 Option 17 (vendor-specific information) provides more configuration options to the iSCSI client. In this 
configuration, three additional suboptions are provided that assign the initiator IQN to the iSCSI boot client along 
with two iSCSI target IQNs that can be used for booting.

The suboptions are listed below.

The content of option 17 should be <2-byte Option Number 201|202|203> <2-byte length> <data>.

Configuring the DHCP Server

Configure the DHCP server to support Option 16 and Option 17.

Note: 

The DHCPv6 standard Root Path option is not yet available. Broadcom suggests using Option 

16 or Option 17 for dynamic iSCSI Boot IPv6 support.

Table 20:  DHCP Option 17 Suboption Definition

Suboption

Definition

201

First iSCSI target information in the standard root path format 

"iscsi:"[<servername>]":"<protocol>":"<port>":"<LUN>":"<targetname>"

202

Second iSCSI target information in the standard root path format 

"iscsi:"[<servername>]":"<protocol>":"<port>":"<LUN>":"<targetname>"

203

iSCSI initiator IQN

Note: 

In 

Table 20

, the brackets [ ] are required for the IPv6 addresses.

Note: 

The format of DHCPv6 Option 16 and Option 17 are fully defined in RFC 3315.

Summary of Contents for NetXtreme BCM57 Series















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands