BriskHeat FE-Series, Instruction Manual

Page: 3 / 38

© BriskHeat
®
Corporation. Tutti i diritti riservati.
74
Cavo scaldante Serie FE Istruzioni di installazione
GUIDA ALLA RISOLUZIONE DEI PROBLEMI
Si prega di leggere questa guida prima di contattare la BriskHeat
®
. Questa guida è stata progettata per
rispondere alle domande più frequenti. Se non si riesce a identificare il problema o si ha bisogno di
ulteriore assistenza, si prega di contattare il distributore locale BriskHeat
®
o contattarci al numero verde
(USA/Canada) 1-800-848-7673 o 614-294-3376 o bhtsales1@briskheat.com .
PROBLEMA SOLUZIONE(I)
L'intero cavo
scaldante non si
riscalda
Verificare se il riscaldatore è collegato alla tensione corretta.
Verificare se c'è una lettura di resistenza (non un circuito aperto) nel
riscaldatore utilizzando un ohmmetro.
Porzione di cavo
scaldante non si
riscalda
Esaminare il modulo non riscaldato se presenta danni.
L'interruttore del
circuito è scattato
Assicurarsi che l'interruttore del circuito sia in grado di gestire l'amperaggio
richiesto del riscaldatore.
Accertarsi che non ci siano danni al riscaldatore e al cablaggio.
Verificare se ci sono circuiti aperti tra il filo bus e la treccina da terra.
Assicurarsi che la lunghezza del riscaldatore non superi la lunghezza massima
del circuito (vedere le tabelle seguenti).
Lunghezza massima del circuito
Cavo
120 VAC
ft (m)
208 VAC
ft (m)
240 VAC
ft (m)
277 VAC
ft (m)
480 VAC
ft (m)
3 W/ft (10 W/m) 640 (195) 1110 (338) 1280 (390) N/A 2560 (780)
8 W/ft (26 W/m) 240 (73) 415 (127) 480 (146) 555 (169) 960 (293)
5 W/ft (16 W/m) 385 (117) 665 (203) 770 (234) N/A 1535 (468)
12 W/ft (39 W/m) 160 (49) 277 (85) 320 (98) 370 (113) 640 (195)
© BriskHeat Corporation. All rights reserved.
3
FE-Series Heating Cable Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
SAFETY ALERT SYMBOL
The symbol above is used to call your attention to instructions concerning your personal safety. It points
out important safety precautions. It means “ATTENTION! Become Alert! Your Personal Safety is
involved!” Read the message that follows and be alert to the possibility of personal injury or death.

Never handle the heater while it is in operation;
always disconnect the heater from the power
source and allow to cool prior to handling.
 Inspect heater and connection kits before use.

Never operate heater without a temperature
control device.

Do not wrap the heating cable over itself.

If spillage of a foreign matter onto heater occurs,
disconnect from power source clean after heater is
allowed to cool.

Never operate a heater without an appropriate
heat sink (device being heated is considered a
heat sink).

Do not operate heater above rated temperature
value.

Fasten heater to device using approved methods
only.

Do not repair damaged or faulty heaters.

Do not crush of apply severe physical stress on
heater or cord assembly

Disconnect heater when not in use
Failure to observe these warnings may result in personal
injury or damage to the heater.

Do not immerse heater in liquid.

Heater must be 5/8 in (13 mm) away from any
combustible material.

Use heater only in approved locations.

Keep sharp metal objects away from heater.
Failure to observe these warnings may result in electric
shock, risk of fire, and personal injury.
A person who has not read and understood all operating
instructions is not qualified to operate this product
DANGER
DANGER
Immediate hazards which WILL result in severe personal
injury or death.
Hazards or unsafe practices that COULD result in severe
personal injury or death.
Hazards or unsafe practices that COULD result in minor
personal injury or property damage.
DANGER
WARNING
End-User Must Comply to the Following:

Only qualified personnel are allowed to connect the
electrical wiring.

Disconnect all supply power at the source before
making any heating cable power input connections.

All electrical wiring must follow local electrical
codes and highly recommend following NEC Article
427.

The person who performs the final installation /
wiring must be qualified for this work.

The end-user is responsible for providing a suitable
disconnecting device.
 The end-user is responsible for providing suitable
electrical protection device. It is highly
recommended that a ground fault circuit breaker be
used.
Failure to observe these warnings may result in personal
injury or damage to the heater.
WARNING
CAUTION
CAUTION