Briggs & Stratton Powersmart 30473 Service And Repair Manual Download Page 4

BRIGGSandSTRATTON.COM

Important Safety Instructions

 

WARNING

 The engine exhaust from this product 

contains chemicals known to the State of California to 
cause cancer, birth defects, or other reproductive harm.

 

WARNING

 Certain components in this product and 

related accessories contain chemicals known to the State 
of California to cause cancer, birth defects, or other 
reproductive harm. 

Wash hands after handling.

 

WARNING

 Running engine gives off carbon monoxide, 

an odorless, colorless, poison gas.
Breathing carbon monoxide could result in death, 
serious injury, headache, fatigue, dizziness, 

vomiting, confusion, seizures, nausea or fainting.

•  Operate this product ONLY outdoors.

•  Install a battery operated carbon monoxide alarm near 

the bedrooms.

•  Keep exhaust gas from entering a confined area through 

windows, doors, ventilation intakes, or other openings.

SAVE THESE INSTRUCTIONS

 - This manual contains 

important instructions that should be followed during 
installation and maintenance of the generator and batteries.

Safety Symbols and Meanings

 The safety alert symbol indicates a potential personal 

injury hazard. A signal word (DANGER, WARNING, or 
CAUTION) is used with the alert symbol to designate a degree 
or level of hazard seriousness. A safety symbol may be used 
to represent the type of hazard. The signal word NOTICE is 
used to address practices not related to personal injury. 

 

DANGER

 indicates a hazard which, if not avoided, 

will

 

result in death or serious injury.

 

WARNING

 indicates a hazard which, if not avoided, 

could

 

result in death or serious injury.

 

CAUTION

 indicates a hazard which, if not avoided, 

could

 

result in minor or moderate injury.

NOTICE

 addresses practices not related to personal injury.

The manufacturer cannot anticipate every possible 
circumstance that might involve a hazard. The warnings in 
this manual, and the tags and decals affixed to the unit are, 
therefore, not all-inclusive. If you use a procedure, work 
method or operating technique that the manufacturer does 
not specifically recommend, you must satisfy yourself that 
it is safe for you and others. You must also make sure that 
the procedure, work method or operating technique that you 
choose does not render the generator system unsafe.

Kickback

Fire

Flying Objects

Hot Surface

Moving Parts

Read Manual

Explosion

Electrical Shock

Toxic Fumes

Explosive Pressure

Chemical Burn

 

WARNING

 

•  This generator does not meet U.S. Coast Guard 

Regulation 33CFR-183 and should not be used on marine 
applications.

•  Failure to use the appropriate U.S. Coast Guard approved 

generator could result in death or serious injury and/or 
property damage.

 

WARNING

 Starter cord kickback (rapid retraction) 

will pull hand and arm toward engine faster than 
you can let go which could cause broken bones, 
fractures, bruises, or sprains resulting in serious 
injury.

•  When starting engine, pull cord slowly until resistance is 

felt and then pull rapidly to avoid kickback.

•  Never start or stop engine with electrical devices plugged 

in and turned on.

Not 

for 

Reproduction

Summary of Contents for Powersmart 30473



































Reviews: