background image

3

Table of Contents

TABLE OF CONTENTS

WARRANTY POLICY

BredaBeds warranties all mechanical hardware for a period of ten (10) years, all wood parts on our products for a period of one 

(1) year to be free of material or workmanship defects and electronics (such as lights) for a period of ninety (90) days. Warranty 

periods begin from date of purchase. We will repair or replace at our discretion any defective parts within this period. This 

warranty is made assuming proper installation using the provided instructions. This warranty does not cover damage due to 

improper use, abuse, neglect, misunderstanding of operation or improper assembly. This warranty does not cover issues with 

springs or pistons. This warranty applies to the original purchaser and is non-transferable. In the unlikely event you have a 

warranty issue, please contact us by phone, email or using the live chat feature when available.

WE DISCLAIM ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES 

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE 

LAW. WE SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. BUYER’S SOLE REMEDY SHALL BE LIMITED 

TO REPLACEMENT OF DAMAGED OR DEFECTIVE PARTS. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY 

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

RETURN POLICY

We will accept returns on any item we sell within a 30 day period from time of receipt, less a 20% restocking fee. Return shipping 

and shipping charges are the responsibility of the customer as well as repackaging the product in a safe and acceptable manner. 

Once the returned product is received by us and inspected for damage, a credit will be issued for the amount of purchase less 

20% and less the cost of any damage, if any. Credit will be applied back to the customer in the same form of payment made 

during the purchase of the product (for example, a credit refund or check) within 3 business days of receipt. Prior to returning 

any product, please contact us for a return authorization.

For more information on our policies, visit https://bredabeds.com/policies or click on

“Warranty, Shipping & Returns” at the bottom of any page on our website.

BredaBed Assembly Instructions Table Of Contents

Title

Page(s)

Warranty and Return Policies

3

IMPORTANT SAFETY INFORMATION - READ THIS FIRST

4

Assembly Tips

5

Unpacking Your BredaBed & Frequently Asked Questions

6

Troubleshooting

7

Parts List: Panels, Hardware Packages & Before You Begin

8-11

Chapter 1: Hardware insertion.

12-16

Chapter 2: Bed Cabinet assembly.

17-20

Chapter 3: Attaching the Bed Cabinet to the wall.

21-24

Chapter 4: Assembling the Bed Face Panel unit.

25-28

Chapter 5: Attaching the Bed Face Panel to the Bed Cabinet.

29-32

Chapter 6: Installing the handles, leg support and mattress.

33-34

Chapter 7: Final adjustment for the Bed Cabinet and springs.

35-36

Chapter 8: Installing hutch options.

37-40

Chapter 9: How to disassemble the bed for moving.

41

Summary of Contents for METROPOLITAN MURPHY










































Reviews: