background image

7

B. 

VERTICALLY WITH NEW CHIMNEY SYSTEM

 (Refer to Figure 7)

NOTE: 

See

 “VENTING” 

and follow L-Vent chimney manufacturer’s instructions.

OPTION:

  To achieve a center vertical installation a 45º elbow and a clean-out tee can 

be used to offset the pipe from the exhaust outlet to the rear center of the stove.

OPTION:

 Install L-Vent elbow in place of clean-out tee. Locate stove. Drop plumb bob 

to center of tee outlet, mark point on ceiling. Install ceiling support and L-Vent pipe per 
L-Vent manufacturer’s instructions.

1.  Always maintain 3” clearance from combustible materials. When passing through 

additional 

fl

 oors or ceilings, always install 

fi

 restop spacer.

2.  After lining up for hole in roof, cut either around or square hole in roof, always 

3” larger all the way around pipe. Install upper edge and sides of 

fl

 ashing under 

roo

fi

 ng materials, nail to the roof along upper edge. Do not nail lower edge. Seal 

nail heads with non-hardening waterproof mastic.

Apply non-hardening, waterproof mastic where the storm collar will meet the vent and 

fl

 ashing. Slide storm collar down until it sits on the 

fl

 ashing. Seal and install cap. 

 

C. 

VERTICALLY INTO EXISTING CHIMNEY SYSTEM

Adapters are available to adapt from 3” L-Vent to 6” or 8” Class-A chimney. (Figure 8a)

As an alternative, 3” or 4” L-Vent can be run inside existing chimney to termination. 
(Figure 8b)
This is the preferred method.

Follow guidelines for equivalent vent length.

INSTALLATION

INSTALLATION

FIGURE 7

FIGURE 8a

FIGURE 8b

Summary of Contents for Classic Cast SPC4000





























Reviews: