background image



CUT

 HERE

WARRANTY INFORMATION CARD

Name__________________________________________ Telephone #: (_____)_____________

City____________________________________________ State_______ Zip_________________

Email Address __________________________________________________________________

Model # of Unit________________________________ Serial #___________________________

Fuel Type:

 

  

Wood 

Coal 

Pellet 

Gas 

Other _________________________

Place of Purchase (Retailer)______________________________________________________

City____________________________________________ State_______ Zip_________________

If internet purchase, please list website address___________________________________

Date of Purchase _______________________________________________________________

Reason for Purchase: 

 

    

Alternative Heat   

Main Heat Source

 

Decoration  

Cost  

Other _________________________

What was the determining factor for purchasing your new USSC appliance?_______

I have read the owner’s manual that accompanies this unit and fully understand the:

Installation 



Operation 

 and 

Maintenance 

 

of my new USSC appliance.

Print Name 

Signature 

Date

Please attach a copy of your purchase receipt.

Warranty not valid without a Proof of Purchase.

Warranty information must be received within 30 days of original purchase.

Detach this page from this manual, fold in half with this page to the inside and tape together. Apply a 
stamp and mail to the address provided. You may use an envelope if you choose.

You may register online by going to www.breckwell.com 

All information submitted will be kept strictly confi dential. Information provided will not be sold for advertising purposes.

Contact information will be used solely for the purpose of product notifi cations. 

Summary of Contents for Classic Cast SPC4000





























Reviews: