background image

IMPORTANT

Read this entire installation manual
to ensure proper installation, then
file the manual with the owner or
maintenance department. 

Flush all the water supply lines
before making connections. 

Wall anchors used must have a
minimum pull-out rating of 1,000
lbs.

Product warranties may be found
under "Product Information" on
our web site at
www.bradleycorp.com.

P.O. Box 309, Menomonee Falls, WI 53052-0309
TEL. 1-800-BRADLEY

FAX  262-251-5817

http://www.bradleycorp.com

Table of Contents

Pre-Installation Information  . . . . . . . . . . . . . . . .2
Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Installation Instructions  . . . . . . . . . . . . . . . . 5-10
Wiring Diagram  . . . . . . . . . . . . . . . . . . . . . . . .10
Cleaning and Maintenance  . . . . . . . . . . . . . . . .11
Soap Dispenser Maintenance  . . . . . . . . . . . .2-13
Assembly of Components  . . . . . . . . . . . . . . .3-14
Check Valve Troublshooting  . . . . . . . . . . . . . .15
Solenoid Valve Troubleshooting  . . . . . . . . . .5-16
Vernatherm™ Mixing Valve . . . . . . . . . . . . . . .17

SS-3/AZ/WH97TAS

Express® Lavatory
System SS-Series

Complies with Texas Accessibility
Standards (TAS) for Juvenile Height
applications.

215-1175 Rev. H; EN 08-805
© 2008 Bradley Corporation
Page 1 of 17

4/24/08

Installation
Instructions
OBSOLETE

Summary of Contents for Express SS Series


















Reviews: