auxiliary command 1 out-
put
auxiliary command 2 out-
put
entry panel enabling out-
put
B IN
bus input from other entry
panels
B OUT
bus output towards recei-
vers or other entry panels
Connector functions
5-pin CN1 connector:
used for con-
nection to VZS/308C in the entry
panel HEP/306 VR.
3-pin CN3 connector:
used for con-
nection to button of HEV/302 VR
entry panel.
1-red:
to button n° 2.
2-orange:
to button n° 3.
3-yellow:
to button n° 4.
WARNING. In installations with a
number of entry panels, call but-
tons must be arranged in the same
order on each.
Connector CN4:
comes ready con-
nected (HEV/301÷302 VR entry
panel).
1-black:
to button no. 1.
2-brown:
to button no. 1.
3-green:
to LEDs lighting the but-
tons.
4-yellow:
to LEDs lighting the but-
tons.
WARNING. Wires belonging to
cables that are not used must be
insulated.
Function of jumpers SW1 and
SW2 (fig. 6)
SW1:
automatic programming of
number of entry panels (default
setting 1).
SW2:
programming of receivers.
Programming of number of entry
panels
(only required where there
is more than one entry panel)
1 -
Start with the last entry panel
connected in series to the bus
(usually the one with terminals
B IN
not connected).
2 -
Remove jumper SW1.
3 -
Wait for the note confirming the
operation (approximately 3÷15 s).
The number of confirmation signals
also indicates the number of pre-
sent and programmed entry
panels (1 signal for the main entry
panel and 1 signal for each secon-
dary entry panel).
4 -
Refit jumper SW1.
Programming receivers
1 -
Remove jumper SW2 from any
entry panel.
2 -
Lift the handset of the receiver
to be programmed (for telephone
sets, see the instructions featured
in interface IT/300).
3 -
Press the door-lock release and
auxiliary 2 buttons at the same time
for at least 1 s (when audio towards
the entry panel is enabled, the
operation is confirmed).
4 -
On the entry panel, press the
call button the receiver is to be
associated with.
3
SW2
P1
SW1
6
VIDEO ENTRY PANEL
HEV/300÷302 VR
Video entry panel for managing the
whole installation.
Teamed with button plates
HEP/306 VR, installations with up
to 64 users can be set up.
For connections to user extensions
the entry panel uses BPT
X2
TECHNOLOGY
bus connection,
enabling all signals involved in
installation to be sent along a
telephone-type single twisted pair
line.
An additional three video-entry or
audio-only entry panels can be
added to the first in series without
the need for other equipment
(selectors, distributors).
The entry panel comes complete
with:
- CCD camera with ±11° manual
angle adjustment both horizontally
and vertically (fig. 4), with fixed-
focus lens (see fig. 5 for dimen-
sions of the target area);
- phonic unit;
- infrared LED for lighting the tar-
get area;
- three potentiometers for the fol-
lowing functions (fig. 4-6):
volume control at entry panel;
volume control at receiver;
P1
timed (in the range 1 to 15 s)
solenoid door-lock release.
The entry panel comes with system
busy and door-lock release buzzer.
The wires supplied make it simple
to connect the entry panel’s
various component units.
Function of each terminal
14÷18V DC
power supply
solenoid lock output
door-lock release button
–
earth for solenoid lock
GB INSTALLATION
INSTRUCTIONS
7
Per montare la placca sulla scatola
incasso avvitare le due viti di fis-
saggio tramite la chiave in dotazio-
ne (fig. 7).
SMALTIMENTO
Assicurarsi che il materiale d’im-
ballaggio non venga disperso nel-
l’ambiente, ma smaltito seguendo
le norme vigenti nel paese di utiliz-
zo del prodotto. Alla fine del ciclo
di vita dell’apparecchio evitare che
lo stesso venga disperso nell’am-
biente.
Lo smaltimento dell’apparecchia-
tura deve essere effettuato rispet-
tando le norme vigenti e privile-
giando il riciclaggio delle sue parti
costituenti.
Sui componenti, per cui è previsto
lo smaltimento con riciclaggio,
sono riportati il simbolo e la sigla
del materiale.
