background image

Appendix

6

64

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 28C • 01/2004

Subject to modifications resulting from technical improvements!

Boulter Buderus Ltd. • http://www.boulter-boilers.com

6.3

Short list of spare parts

The following are parts commonly required due to damage or expendability. Their failure or absence is likely to affect safety or 
performance of this appliance. For a pictorial representation of the part see the respective position number on the exploded view 
pictures on page 7.

Description

Product No.

480

Gas valve

73645

490

Venturi 24 kW

73641

500

Gas pipe

73644

510

Suction pipe

73646

520

UBA 3

18196

530

Room control converter

78079

540

Cable harness 24V

73695

550

Cable harness 230V

73779

560

BC10 mount

73692

570

Backpanel mounting plate

73693

580

Backpanel KIM

73694

590

Sensor flow detection

38353

600

Transformer

73697

610

Sensor CH and outflow

38352

620

Hot water tank

73654

630

DHW pipe (hot)

73650

640

DHW pipe (cold)

73652

650

Hot water flow regulator

73656

660

Connection

73655

670

Pump Uper 15-50-130

73674

680

Electronic pressure sensor

73678

690

Return pump connection

73676

700

Return connection

73583

710

Actuator three-way valve

73686

720

Cartridge three-way valve

73685

730

Three-way valve without actuator

73688

740

Clip actuator

73687

750

Power switch

73660

760

Return pipe 

73781

770

Pressure relief valve 3 bar

73199

780

Sanitary supply pipe

73683

790

Supply manifold

73682

800

By-pass

73681

810

Expansion vessel pipe

73691

820

Expansion vessel

73718

830

Seal 125 mm

73737

840

Seal frame/syphon

73561

850

Insulation casing

73732

860

RCC connection box

73720

KIM 1024

73778

Nipple ½"

73780

Connection green

73773

Connection orange

73777

Connection red

73776

Connection blue

73775

Connection turquoise

73772

Description

Product No.

10

Casing (incl. insulation)

73624

20

Door control panel

73782

30

Ventilation cover

73647

40

Sealing ventilation cover

73649

50

Latches (set of 2 pc.)

73648s

60

Assembly casing block (set of 2 pc.)

38458s

70

Insulation frame

73733

80

Bracket

38092

90

Seal top (2 pc.)

73632s

100

Seal bottom (2 pc.)

73633s

110

Seal (set of 10 pc.)

73677s

120

Cover flue gas adaptor (80/125)

73628

130

Flue gas adaptor

73626

140

Seal 60 mm 

73563

150

Exhaust pipe

73629

160

Seal 60 mm

73736

170

Condensate collector

73630

180

Flue gas sensor

73376

190

Seal exhaust pipe

73579

200

Syphon

73631

210

Drain pipe syphon

73717

220

Flex. drain pipe syphon

73508

230

Flow connection piece

73672

240

Automated air vent

38618

250

Bi-sensor

73673

260

Seal (set of 2 pc.)

73584s

270

O-ring (set of 10 pc.)

73580s

280

Supply pipe

73671

290

Clip (set of 5 pc.)

73653s

300

Gas/air supply

73663

310

Hot surface ignitor

78105

320

Ionisation electrode

38320

330

Seal (set of 5 pc.)

73665s

340

Seal (set of 5 pc.)

73666s

350

Gas/air supply valve (set of 5 pc.)

73756s

360

Seal fan (set of 5 pc.)

73640s

370

Seal burner (set of 2 pc.)

73669s

380

Burner

73668

390

Heat exchanger

73659

400

Frontside heat exchanger

73658

410

Latches (set of 2 pc.)

73661s

420

Divider combustion gas

73670

430

Sight glass

73662

440

Seal heat exchanger

73578

450

Back panel heat exchanger

73657

460

Seal heat exchanger / gas/air supply

73728

470

Fan

73639

Summary of Contents for Benchmark 600 Series









































































Reviews: