4-4
190 Outrage
Section 4 • Electrical System
R
The following pages contain electrical schematics
pertaining to the electrical system in your boat. These
schematics were generated by technicians in the
Boston Whaler
®
Engineering Department and are for
reference and to be used by service technicians.
Boston Whaler
®
does not recommend that you
attempt to work on the electrical system yourself.
Instead, we suggest that you take your boat to an
authorized Boston Whaler
®
dealer for electrical
service.
Boston Whaler
®
reserves the right to change or
update the electrical system on any model at any time
without notice to the customer and is not obligated to
make any updates to units built prior to the change.
Wiring Identifi cation Chart
Boston Whaler
®
adheres to electrical wiring
requirements which meet all the ABYC-11 standards.
The following chart outlines the gauge, color and
function of the wiring used.
Electrical Schematics & Harnesses
BRN/ORN
SUMP PUMP
BRN/RED
BILGE PUMP (UNSWITCHED)
BRN/WHT
MACERATOR
GRY
RUNNING LIGHTS
GRY/BLK
ACC 1
GRY/BLU
ACC 2
GRY/GRN
ACC 3
GRY/RED
AFT MAST/ACC 4
GRY/WHT
ALL ROUND/FWD MAST LIGHT
ORN
REFRIGERATOR or CENTER
WIPER
ORN/BLU
HORN
ORN/BRN
STARBOARD WIPER PARK
ORN/GRN
STARBOARD WIPER
ORN/RED
PORT WIPER
ORN/VIO
VACUUM PUMP
ORN/WHT
CENTER WIPER
PINK
FUEL SENDER
RED
12V RECEPTACLE
VIO
IGNITION
WHT
CO MONITOR/ELECTRIC TRIM
TAB (SWITCHED)
YLW
BLOWER/STEREO MEMORY
YLW/RED
START
COLOR
FUNCTION
GRN
GROUNDING MAIN/TOWER &
ALUMINUM FUEL TANKS
GRN
GROUNDING
ORN
STARBOARD 30 AMP
RECEPTACLE
RED
MAIN FEEDS/PORT 30 AMP
RECEPTACLE
BRN/BLK
STARBOARD FISHBOX PUMP
BRN/VIO
FORWARD FISHBOX PUMP
BRN/YEL
LIVEWELL PUMP
(HIGH CURRENT)
BRN/BLU
PORT FISHBOX PUMP
RED
+12V MAIN
BLK
GROUND
BLK/YEL
STOP CIRCUIT
BLK/WHT
GEN SHUTDOWN
BLU
COMPASS
BLU/BLK
DOME LIGHT
BLU/GRN
SPREADER LIGHT
BLU/ORN
LIVEWELL LIGHT
BLU/RED
COURTESY LIGHTS
BLU/VIO
CABIN LIGHTS
BRN
BILGE PUMP (SWITCHED)
BRN/GRY
RAW WATER
BRN/GRN
FRESH WATER
COLOR
FUNCTION
Wire Color Chart for DC and Special Circuit
Rigging
Your boat has a rigging trough above the fuel tank
and below the
fl oor to allow the owner to run new
wiring for electronics. There is a pull cord installed
in the trough with the ends bundled and tied at
either end of the tube. The ends are located in the
aft bilge and inside the console where it exits the
rigging trough. Tie another piece of nylon cord to
the current accessory wiring being run and use that
for later runs.
Rigging Trough/Pull
Fig. 4.4.1
1
2
1
3
2
3
RIGGING TROUGH
FORWARD PULL CORD
AFT PULL CORD
Summary of Contents for 190 Outrage
