manualshive.com logo in svg

Bosch Singular 4000, Service Manual, Page: 52 / 68

Share
Download
Bosch Singular 4000 Service Manual Download Page 52

5 2

 |

 

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

8.19     E7 Error (Abnormal Operation: Gas Valve Relay)

Error

Description

Gas valve relay error

It occurs when the gas valve relay which is mounted on control board is stuck closed.

Checkpoint

 

Replace the control board

Table 39

8.20     EB Error (Hot Water Overheating)

Error

Description

Overheating of temperature sensor

(Boiling superheat) over 176 °F

An error is displayed when abnormal overheating caused by Hot water sensor

Checkpoint

 

Check the resistance of Temperature sensor (NTC method)

 

—

Measurement should be carried out after separating the sensor.

Table 40

Figure 81

An error occurs when the 

water temperature is 176 °F 

(80 °C) or below 

Replace the temperature 

sensor

Check the resistance of the 

temperature sensor

Resistance   

<= 3.5 kΩ

Yes

No

86 °F: 40 kΩ (± error possible)
140 °F: 12.4 kΩ
185 °F: 3.9 kΩ

Replace the control board

Summary of Contents for Singular 4000





































































Reviews:

No comments