Bosch Singular 4000 Service Manual Download Page 27

Page: 27 / 68

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

8.5 A6 Error (Ignition Error)

Error

Description

Ignition Failure

When it is judged that ﬂ ame is not recognized in normal combustion condition, ignition is attempted 6 times repeatedly. Ifthe
ﬂ ame is not recognized, ignition is not attempted again and an error is issued

Checkpoint



Check if the main gas valve is closed.



Check the operation condition of the gas valve (attempting to ignite)

—

Wire color: White-White (DC 105 – 135 V)



Check the assembly and operation condition of the automatic igniter

1. Check the discharge state
2. Check the input voltage part of the automatic igniter Wire color: Brown-Brown (AC 105 – 135 V)

Table 28

Figure 18

Replace the

ignition transformer

Replace the

electrode assembly

Replace the flame rod

Check the 1st gas

pressure

Replace the gas valve

Ignition miss

Check the

ignition transformer

voltage

Ignition

condition

(Check flame)

Check the

gas valve input

voltage.

Check the

gas valve coil for

disconnection

Check the

ignition transformer

operation

Check

the operation of

the gas valve

Yes

Replace the

control board

Replace the control board

Summary of Contents for Singular 4000





































































Search results

Summary of Contents for Singular 4000

Reviews:

Bosch Singular 4000, Service Manual, Page: 27 / 68

Search results

Summary of Contents for Singular 4000

Reviews: