manualshive.com logo in svg

Bosch Singular 4000, Service Manual, Page: 31 / 68

Share
Download
Bosch Singular 4000 Service Manual Download Page 31

   

 

 

| 

31

 

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

8.8     A9 Error (Exhaust Temperature Sensor Error) 

Error

Description

Exhaust temperature

sensor error

 

Freeze prevention error due to a temperature decrease of the heating water

 

—

Heating water temperature <= 43 °F: Combustion in progress

 

—

Heating water temperature >= 104 °F: Combustion stopped

Checkpoint

 

Check if the heating water temperature is <= 43 °F

 

Check if the heating water sensor connection is OPEN

 

Check the resistance of the heating water sensor

Table 30

Figure 28

Check the assembly of 

the heating water sensor 

connector and reassemble it

Replace the temperature 

sensor 

Operated when 

the heating water 

temperature is 

<=42 °F

Is the   

temperature sensor 

resistance normal?

Yes

Yes

No

No

86 °F: 40 kΩ
140 °F: 12.4 kΩ
185 °F: 3.9 kΩ

Replace the control board

Replace the control board

Summary of Contents for Singular 4000





































































Reviews:

No comments