manualshive.com logo in svg

Bosch Singular 4000, Service Manual, Page: 15 / 68

Share
Download
Bosch Singular 4000 Service Manual Download Page 15

   

 

 

| 

15

 

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

7.9     Secondary Heat Exchanger

Part No.

7738007256*

Function

 

Main part for heat transfer from the burner

 

It has multiple paths of water tubes on the heat exchanger surface as 

well as inside the combustion chamber.

Failure Event

 

Water and/or exhaust gas leakage through a crack

 

Improper heat transfer can cause the water in the heat exchanger to 

boil due to possible scale formation

Effects

 

Leakage of exhaust gas

 

Excessive heating of water that produces boiling noises.

Error Code

AA, A4

Diagnostic

 

Visual inspection : Check if there is a crack on the surface of heat 

exchanger.

 

Sound inspection : Check if boiling occurs inside the unit

Color/Number of Wires

N/A

Table 12

* part number is for fully assembled heat exchanger unit.

7.10     Sensor

Part No.

7738007297 (Sensor, Supply/Return)

Sensor, Heating/Return

Sensor, DHW

Exhaust Temperature Sensor (Blue)

7738007295 (Sensor, DHW)

7738007268 (Exhaust Temperature Sensor)

Function

Measure the temperature of the hot water, cold water, exhaust gas in the 

boiler.

Failure Event

Unable to properly measure the temperature in the boiler.

Effects

 

Unable to shut combustion off when the water temperature from the 

heat exchanger exceeds 203°F (95°C).

 

Unable to reach the hot water temperature set by user.

 

Unable to shut down the water heater when the flue gas temperature 

from the exhaust duct exceeds 203°F (95°C).

Error Code

AA, AB, AC, E1, E2, E3, EB

Diagnostic

 

Visual inspection: Connection or breakage of wires.

 

Voltage check: Check range of voltage shown below.

 

Resistance check of the sensor.

Color/Number of Wires

 

Blue-Blue: DC 0 – 5 V

Table 13

Summary of Contents for Singular 4000





































































Reviews:

No comments