manualshive.com logo in svg

Bosch Singular 4000, Service Manual, Page: 48 / 68

Share
Download
Bosch Singular 4000 Service Manual Download Page 48

4 8

 |

 

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

8.17     E3 Error (Abnormal Operation: Return Sensor)

Error

Description

Return Sensor Error

Error is displayed when the Return sensor has short-circuited or is disconnected

Checkpoint

 

Check if the Hot Water Thermistor connector is connected normally.

1.  Control board wire
2.  Return sensor wire

 

Measure the check the resistance of the Return sensor (NTC method).

 

—

Separate the sensor and measure it at room temperature.

 

Check the Return sensor for disconnection

 

Check the Return sensor for short-circuit

Table 37

Figure 71

Check the assembly 

condition of the control board 

and the temperature sensor 

connector and reassemble 

the control board and the 

temperature sensor connector

Replace the temperature 

sensor

Replace the temperature 

sensor

Replace the control board

Check the 

temperature 

sensor for short 

Is the   

resistance of the 

temperature sensor 

normal?

No

Yes

Yes

No

86 °F: 40 kΩ (± error possible)
140 °F: 12.4 kΩ
185 °F: 3.9 kΩ

Summary of Contents for Singular 4000





































































Reviews:

No comments