manualshive.com logo in svg

Bosch Singular 4000, Service Manual, Page: 29 / 68

Share
Download
Bosch Singular 4000 Service Manual Download Page 29

   

 

 

| 

29

 

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

8.6     A7 Error (Abnormal Operation: Gas Valve Relay) 

Error

Description

Gas valve relay error

It occurs when the gas valve relay which is mounted on PCB is stuck closed.

Checkpoint

Replace the control board

Figure 23

8.7     A8 Error (Abnormal Operation: Gas Valve) 

Error

Description

Flame after combustion

This error occurs if fl ame is detected after burner had shut off .

Checkpoint

 

Check the operation condition of the gas valve

 

 Whether the flame rod is damaged or not

 

 Whether the flame rod comes into contact with the metal burner or not

Table 29

Figure 24

Replace the control board

Replace the flame rod

Replace the gas valve

Combustion stop

Separate the flame rod wire 

and attempt operation again

Combusted

Check   

if the gas valve is 

closed

Check if  

the flame rod is 

damaged or not

Yes

Yes

No

No

No

Yes

Summary of Contents for Singular 4000





































































Reviews:

No comments