Bosch Rexroth IndraControl XFE 01.1 Series Operating Manual Download Page 6

Page: 6 / 36

6 / 36

IndraControl XFE 01.1

Customer feedback

Bosch Rexroth AG

R911345570, Edition 06

This document instructs the technical staff of the machine manufacturer on how to safely perform the

mechanical and electrical installation and on how to commission the device.
Required qualification: Individual who is able to assess the tasks assigned and to identify possible

safety risks owing to qualification in the subject, knowledge and experience. The individual should also

be familiar with the standards and regulations.

1.3

Scope

This document is valid for all variants of the modules, whose type code starts with: XFE01.1-FB ...

The type code specifications are located on the type plate of the module. Also refer to

⮫

Chapter 2.1

“ Product identification and type plate ” on page 7

1.4

Related documents

Table 2: Related documents

Title

Part number and document type

IndraControl XM21, XM22
Controls

⮫

R911340667

Operating Instructions

IndraControl XM42
Controls

⮫

R911345566

Operating Instructions

For related documents, go to the Rexroth Media Directory at

⮫

http://www.boschrexroth.com

and

enter the specified part number.

1.5

Customer feedback

Customer requests, comments or suggestions for improvement are of great importance. Please email

your feedback on the documentations to

⮫

[email protected]

. Directly insert

comments into the electronic PDF document and send the PDF file to Bosch Rexroth.

Summary of Contents for Rexroth IndraControl XFE 01.1 Series





































Search results

Summary of Contents for Rexroth IndraControl XFE 01.1 Series

Reviews:

Related manuals for Rexroth IndraControl XFE 01.1 Series

Brands by name

Popular brands

Bosch Rexroth IndraControl XFE 01.1 Series, Operating Manual

Search results

Summary of Contents for Rexroth IndraControl XFE 01.1 Series

Reviews:

Related manuals for Rexroth IndraControl XFE 01.1 Series

Brands by name

Popular brands