Bosch Rexroth IndraControl XFE 01.1 Series Operating Manual Download Page 5

Page: 5 / 36

5 / 36

IndraControl XFE 01.1

Overview on target groups and product phases

Bosch Rexroth AG

R911345570, Edition 06

About this documentation

1.1

Change record

Table 1: Editions of this documentation

Edition Release

date

Note

2014-10 First edition

2016-08 CAN modules and Sercos modules supplemented

2016-10 Corrections

2017-02 Explosion protection notes and type plate supplemented

2019-06 Standards and warning instructions modified for UL, explosion protection notes

removed

2021-08 Description of the LEDs "SF" and "BF" supplemented for the RT-Ethernet module

1.2

Overview on target groups and product phases

In the following illustration, the framed activities, product phases and target groups refer to the present

documentation.
Example: In the product phase “Mounting (assembly/installation)”, the target group “Mechanic/electri-

cian” can execute the activity “install” using this documentation.

Presales Aftersales

Selection

Mounting

(assembly/installation)

Engineering

Commissioning

Operation

Decommissioning

Product

phases

Target

groups

Activities

Design engineer

Programmer

Technologist

Process

specialist

Select

Prepare

Design

Construct

Mechanic/

electrician

Unpack

Mount

Install

Programmer

Commissioning engineer

Parameterize

Program

Configure

Simulate

Technologist

Process specialist

Optimize

Test

Machine

operator

Maintenance

technician

Service

Operate

Maintain

Remove

faults

Create the

NC program

Mechanic/

electrician

Disposal company

Dismount

Dispose

Fig. 1: Assigning the present documentation to the target groups, product phases and activities of the

target group

About this document

ation

Summary of Contents for Rexroth IndraControl XFE 01.1 Series





































Search results

Summary of Contents for Rexroth IndraControl XFE 01.1 Series

Reviews:

Related manuals for Rexroth IndraControl XFE 01.1 Series

Brands by name

Popular brands

Bosch Rexroth IndraControl XFE 01.1 Series, Operating Manual

Search results

Summary of Contents for Rexroth IndraControl XFE 01.1 Series

Reviews:

Related manuals for Rexroth IndraControl XFE 01.1 Series

Brands by name

Popular brands