Bosch D621 Series User Manual Download Page 59

Page: 59 / 62

D621 Series

User's Guide | Glossary

Bosch Security Systems | 8/04 |

Faulted Point

Point that is not normal, such as an open
door or window.

Fire Alarm
Tone

Warble tone that is on for one second and
then briefly off (repeatedly).

Fire Point

Type of 24-Hour Point that only monitors a
fire detection device(s), such as a smoke
detector. This type of point is always on
and cannot be turned off.

Hold

Instruction to press and hold a key to
perform a function.

No Delay

Turns the system on without entry or exit
delay.

Non-Fire Point Type of 24-Hour Point that is always on

and cannot be turned off.

Off Display

Display that appears when the system is
turned off and no keys are pressed.

Part On

Turn on part of the points in the system.
Part On points are determined by your
security company.

Part 2 On

Turn on part of the points in the system.
Part 2 On points are determined by you,
the user.

Point

Detection device or group of devices
connected to your security system.

Press/Push

Interchangeable terms instructing you to
push down and then release a key.

Trouble

Service condition that needs to be
corrected, such as a broken wire.

Trouble Tone

Warble tone that is on briefly, followed by
a pause, and then followed by the warble
tone (repeatedly).

Summary of Contents for D621 Series































































Search results

Summary of Contents for D621 Series

Reviews:

Related manuals for D621 Series

Brands by name

Popular brands

Bosch D621 Series, User Manual

Search results

Summary of Contents for D621 Series

Reviews:

Related manuals for D621 Series

Brands by name

Popular brands