Bosch AutoDome Junior HD VJR Series Installation Manual Download Page 82

Page: 82 / 194

en | Audio, Alarms and Relay Connections

AutoDome Junior HD

F.01U.275.803 | 6.0 | 2012.11

Installation Manual

Bosch Security Systems, Inc.

Audio, Alarms and Relay
Connections

9.1

Alarm Input

All AutoDome Junior models provide connections for two alarm

inputs, one alarm output, and one audio input. Each alarm input

can be activated by dry contact devices such as pressure pads,

passive infrared detectors, door contacts, and similar devices.

Figure 9.1

Six-wire Audio and Alarm In/Out Cable

The table below summarizes the size and distance wires.

Table 9.1

Alarm Wire Guide

You wire alarms either Normally Open (N.O.) or Normally

Closed (N.C.), and must program the alarm inputs N.O. (the

default) or N.C. through the AutoDome Junior main menu.

Wire Color Function

White

Alarm Out

Brown

Alarm In 1

Orange

Alarm In 2

Green

Ground

Yellow

Audio In

Blue

Audio Ground

Wire Size

Maximum Distance

AWG

feet meters

0.644

500 152.4

18 1.024

800 243.8

ALARM OUT

ALARM IN 1

ALARM IN 2

GR
OUND

UDIO GND

UDIO IN

WHT

BRN

ORG

GRN

YEL

Summary of Contents for AutoDome Junior HD VJR Series



































































































































































































Search results

Summary of Contents for AutoDome Junior HD VJR Series

Reviews:

Related manuals for AutoDome Junior HD VJR Series

Brands by name

Popular brands

Bosch AutoDome Junior HD VJR Series, Installation Manual

Search results

Summary of Contents for AutoDome Junior HD VJR Series

Reviews:

Related manuals for AutoDome Junior HD VJR Series

Brands by name

Popular brands