Bosch AutoDome Junior HD VJR Series Installation Manual Download Page 183

Page: 183 / 194

AutoDome Junior HD

Troubleshooting | en

183

Bosch Security Systems, Inc.

Installation Manual

F.01U.275.803 | 6.0 | 2012.11

Problem

Solution

No Network

Connection

–

Check all network connections

–

Ensure that the maximum distance

between any two Ethernet connections is

100 m (328 ft) or less.

If O.K., then:

–

If you are behind a firewall, ensure that the

Video Transmission mode is set to UDP.

Access the Settings Web page for the IP-

enabled device.

Expand the Service Settings link, then

click Network.

Select UDP from the Video Transmission

drop-down list. Then click Set.

Video is distorted

(AutoDome Junior HD)

–

Navigate to the SETTINGS page.

–

Click the Advanced Link; then click the Camera

link, located in the left pane of the Settings

window.

–

Click the Installer Menu, located under the

Camera link.

–

Select either 50 or 60 Hz from the Frequency

pull-down list.

Summary of Contents for AutoDome Junior HD VJR Series



































































































































































































Search results

Summary of Contents for AutoDome Junior HD VJR Series

Reviews:

Related manuals for AutoDome Junior HD VJR Series

Brands by name

Popular brands

Bosch AutoDome Junior HD VJR Series, Installation Manual

Search results

Summary of Contents for AutoDome Junior HD VJR Series

Reviews:

Related manuals for AutoDome Junior HD VJR Series

Brands by name

Popular brands