Bosch Automation CPS21_3 Manual Download Page 80

Page: 80 / 107

Display and Control Elements

7–8

1070 073 825-103 (02.04) GB

7.3

LED Indicators

7.3.1

Hardware Indicators

The PC system is provided with 5 LEDs for indications on hardware. In the
case of the CPS21_4 the LEDs are not labeled. The assignments are the
same as for the CPS21_3 (see illustration).

5 LED indicators

Please take appropiate measures if one of the following LEDs indicates an
error or a message:

LED

Display

Meaning

Measures

LED green

Standard operation

–

LED off

No supply voltage 24 VDC

Check the supply vol-
tage at the power sup-
ply unit!

VOut

LED green

Standard operation

–

LED off

Internal v5V / +12V not
available

Check the supply vol-
tage at the power sup-
ply unit!

LED yellow

Access to hard disk

–

Temp

LED off

Standard operation

–

LED flashes
red

Internal housing temperature
exceeds > 50

C. Shutdown

will occur if temperature conti-
nues to rise.

Lower ambient tempe-
rature!
Check fan of PC!

UPS

LED off

Standard operation

–

LED red

CPS21 currently running on
battery power, i.e. no mains
power available!

Restore mains power,
initiate a controlled
CPS21 restart!

LED flashes
red

Discharged or defective re-
chargeable battery, or battery
not connected.

Check battery!
Observe 5 hour re-
charging time!

Summary of Contents for CPS21_3












































































































Search results

Summary of Contents for CPS21_3

Reviews:

Related manuals for CPS21_3

Brands by name

Popular brands

Bosch Automation CPS21_3, Manual

Search results

Summary of Contents for CPS21_3

Reviews:

Related manuals for CPS21_3

Brands by name

Popular brands