Bosch Automation CPS21_3 Manual Download Page 76

Page: 76 / 107

Display and Control Elements

7–4

1070 073 825-103 (02.04) GB

7.2

Keyboard

The front panel is provided with a medium resistant membrane keyboard (IP
65). It contains 57 keys (or buttons), 15 of which are provided with an LED.
Some keys can be assigned multiple functions.

In addition, 3 buttons are integrated in the front panel:

START, illuminated

STOP

EMERGENCY OFF

7.2.1

Block of Function Keys

The following key blocks belong to those keys whose function can be pro-
grammed by means of the application program:

8 keys arranged horizontally below the display
(e.g., for the softkey functions customary in industry)

Description of this key row: F1...F8

4 keys F9...F12, arranged horizontally below the F1...F8 function key
block

Description of this key row: provided by the user

(description

tags)

2 x 3 navigation buttons vertically arranged on the right and left side of the
display inside the handlebar.

Designation: none

Navigation keys

Function keys
F1..F8

Handlebar

Navigation keys

Function keys
F9..F12

Summary of Contents for CPS21_3












































































































Search results

Summary of Contents for CPS21_3

Reviews:

Related manuals for CPS21_3

Brands by name

Popular brands

Bosch Automation CPS21_3, Manual

Search results

Summary of Contents for CPS21_3

Reviews:

Related manuals for CPS21_3

Brands by name

Popular brands