Bolderton 716240 Manual Download Page 5 | Manualshive

Page: 5 / 24

Bolderton 716240 Manual Download Page 5

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.

This instruction manual complies with the ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.

ATTENTION!!

WHEN YOU SEE A “ WARNING!” BE SURE TO HEED THE MESSAGE!

THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!

STEP 4.

Once you have reached your desired height, insert the tree belt through

the  loop  of  the  tether  (Fig.  5). Then,  carefully  wrap  the  tree  belt around  the  tree
at  a  height  that  allows  just  enough  slack  for  you  to  sit comfortably  in  your  stand.
Keeping  the  tether  as  short  as  possible  limits the  distance  you  will  travel,  in  the
unlikely  event  you  shall  experience  a fall. To secure the tree belt, insert the free
end up through the slot in the buckle closest to opposite end of the tree belt, then
cross over the sliding mechanism and back down through opposite slot. Pull on tree
belt to secure and test to make sure sliding mechanism engages, creating secure tree
belt placement (Fig. 6, 7, 8).

WARNING!

It is very important to complete this Step of the assembly. An improperly

secured buckle

may cause full-body fall arrest harness failure resulting in serious

injury or death! If there is not enough strap available to complete this step,

DO

NOT USE THIS FULL-BODY FALL ARREST HARNESS!

You may need to purchase

and use a larger specialty sized full-body fall arrest harness that complies with ASTM

standards.

tree

belt

Tree Belt

Side View

Slot A

Left Leg

Strap

Right Leg

Strap

3 Bar

Buckle

Up through Slot B

Down through Slot A

Down through Slot B

Pull tight to secure

Back over top

Slot B

FIG 4

FIG 6

FIG 8

FIG 7

Sitting/

Seating

tree

belt

tether

tree

belt

Standing

tether

shoulder

strap

shoulder

strap

shoulder

strap

shoulder

strap

Leg Strap

waist

belt

Leg Strap

FIG 2

shoulder

strap

shoulder

strap

shoulder

strap

shoulder

strap

Leg Strap

waist

belt

Leg Strap

FIG 3

Tether

Tether

Loop

Tether

Loop

3 Bar

Buckle

3 Bar

Buckle

Front View

Rear View

SRD Strap

Right

Waist

Loop

Right

Leg Strap

Right

Leg Strap

Left

Leg Strap

Left

Leg Strap

Left

Waist

Loop

Tether

SRD Strap

FIG 1

tree belt

tether

FIG 5

5

«
...
3
4
5
6
7
...
»

Summary of Contents for 716240

























Reviews:

No comments