Bolderton 716240 Manual Download Page 4

ATTENTION!! 

WHEN YOU SEE A “  WARNING!” BE SURE TO HEED THE MESSAGE!

THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.

This instruction manual complies with the ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.

STEP 1.

  Identify  the  main  parts  of  the  full-body  fall  arrest  harness  (Fig. 1). Hold the

full-body fall arrest harness by the tether loop insuring the harness is upright and leg

straps are hanging down. Straighten any parts that have become twisted. Insert arms 

through each shoulder strap (Fig. 2).

STEP 2.

  Feed  the  left  leg  strap  between  legs  and  thread  through  the bottom left 

waist loop. Repeat with the right leg strap, feeding between legs and through right

waist loop (Fig. 3).

STEP 3.

  Secure the two leg straps by threading the three bar buckle (Fig. 4). Tighten

the leg straps snugly.  

DO NOT

 legs. Full-body fall arrest harness shall look like the one depicted in Figure 5 when donned  

correctly. 

FULL-BODY FALL ARREST HARNESS INSTRUCTIONS

FULL-BODY FALL ARREST HARNESS USAGE INSTRUCTIONS & WARNINGS

 WARNING!

 

Failure to read and strictly comply with the instructions contained  

here may result in serious injury or death!

READ THE FULL-BODY FALL ARREST HARNESS SECTION CAREFULLY AND FOLLOW

 

ALL OF THE INSTRUCTIONS! YOUR  FULL-BODY FALL ARREST HARNESS AND ITS 

COMPONENT (I.E., LANYARD/TETHER, TREE BELT, CLIMBING BELT (LINEMAN’S BELT

 

AS APPLICABLE), SUSPENSION RELIEF DEVICE) IS DESIGNED FOR A MAXIMUM 
CAPACITY (USER AND EQUIPMENT) OF 3

5

0 POUNDS (1

58

kg). ADDITIONALLY, YOUR

 

FULL-BODY FALL ARREST HARNESS (AND ITS COMPONENTS) MUST BE REPLACED 

AFTER 

FIVE 

(

5

) YEARS OF SERVICE!

 WARNING!

 Prior to attempting to use this or any other Bolderton product(s)

 

you must take a moment and become familiar with its assembly, setup installation, use 

 

and removal. You must practice installing, setting-up and using your full-body fall arrest 

 

harness and its components (i.e., lanyard/tether, tree belt, suspension relief device, 

 

climbing belt/lineman’s belt [as applicable]) at ground-level prior to attempting to use 

 

it at heights above ground-level. Once you have become thoroughly knowledgeable and 

 

comfortable with this product(s) assembly, setup, installation, use and removal at ground-

 

level, you are now ready to use it at heights above ground-level. Failure to follow these 

 

instructions may result in serious injury or death!

 WARNING!

 You must wear a 

Fall Arrest System (FAS)

 comprising of a full-body 

fall  arrest  harness,  lanyard/tether,  tree  belt,  suspension  relief  device and climbing 

belt/lineman’s belt (as applicable) at all times after leaving the ground. You must stay

Single safety belts and chest harness are no longer allowed and shall never be used. 

If you are not wearing a full-body fall arrest harness (that is connected to the tree) 

that is protecting you from a fall, do not leave the ground. Failure to follow these  

instructions may result in serious injury or death!

 WARNING!

 

 

ALWAYS 

practice using your full-body fall arrest harness (FAS) in the 

presence of a responsible adult prior to using it in an elevated hunting environment, 

and learn what it feels like to hang suspended in the harness at ground level. Practice  

installing and using your treestand at ground level and with a responsible adult present  

before you go hunting.

 WARNING!

 The length of the full-body fall arrest harness lanyard/tether must be 

kept to a minimum at all times during use. It shall be adjusted so that it is above the 

head with no slack (snug) in the sitting position and you shall have  the  minimum 

amount  of  slack  possible  when  climbing.  Never  let  the tether strap get under your 

chin or around your neck. Failure to follow these instructions may result in serious 

injury or death!

 WARNING!

  Shall  you  experience  a  fall  there  is  time  to  make  a  correct decision 

on what action needs to take place. It is important to remember: 

DO NOT PANIC!

Failure to follow these instructions may result in serious injury or death! 

 WARNING!

  If  you  have  a  limiting  physical  and/or  health  condition  that precludes 

and/or  renders  you  incapable  of  self-recovery  and/or  a  suitable escape plan is not 

available

,

 

DO NOT

 hunt from heights above ground-level. Failure to follow these instructions  

may result in serious injury or death!

 WARNING!

 

FALLS FROM A TREESTAND CAN OCCUR ANYTIME AFTER LEAVING 

THE 

GROUND. THESE FALLS COULD RESULT IN EITHER SERIOUS INJURY OR DEATH! FOR 

YOUR PERSONAL SAFETY, PLEASE TAKE A MOMENT TO CAREFULLY READ THIS PRODUCT

INSTRUCTION MANUAL IN ITS ENTIRETY BEFORE ATTEMPTING TO ASSEMBLE, SET- 

UP, INSTALL, REMOVE, AND/OR OTHERWISE USE THIS BOLDERTON PRODUCT(S). AT 

LEAST ANNUALLY, REVIEW THE CONTENTS OF THIS INSTRUCTION MANUAL 

AND 

WATCH THE “

TREESTAND SAFETY: IT’S UP TO YOU” 

DVD. 

ADDITIONALLY,

  

KEEP 

 

THESE INSTRUCTIONS FOR THE ENTIRE DURATION THAT YOU OWN THIS BOLDERTON 

PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY 

OR DEATH! 

 WARNING!

 THE SAFE USE AND OPERATION OF THIS BOLDERTON PRODUCT IS THE 

SOLE RESPONSIBILITY OF THE USER. IT IS ALSO THE SOLE RESPONSIBILITY OF THE OWNER 
TO  PROVIDE  ANY  PERSON(S) WHO  BORROW  OR  PURCHASE THIS PRODUCT FROM  
THEM WITH THESE COMPLETE INSTRUCTIONS. FAILURE TO FOLLOW THESE INSTRUCTIONS 
MAY RESULT IN SERIOUS INJURY OR DEATH! ADDITIONALLY, FAILURE TO FOLLOW THESE 
INSTRUCTIONS MAY SUBJECT YOU TO PERSONAL LIABILITY PENALTIES AS DETERMINED 
BY THE U.S. JUDICIAL SYSTEM.

 WARNING!

 Practice the use of your Bolderton full-body fall arrest harness and 

Suspension  Relief  Device  (SRD)  at  ground-level,  in  the  presence  of  a responsible 

adult to experience the feeling of hanging  suspended  before using in a hunting 

environment. Failure to follow these instructions may result in serious injury or death! 

 WARNING!

  

NEVER

 allow the full-body fall arrest harness lanyard/tether to get under 

your chin or around your neck. This poses a choking hazard that can lead to serious injury 

or death. Failure to follow these instructions may result in serious injury or death! 

 

WARNING!

 

If your hunting location is unknown by anyone and communication 

for self-recovery/escape shall

you experience a fall. Prolonged suspension in a full-body fall arrest harness can be fatal.  

It is important to exercise the legs by pushing against the tree or doing other forms 

of continuous leg exercises to avoid blood pooling while being suspended. Varying 

degrees of physical ÿtness may require di°erent plans for self-recovery/escape and   

to counter the e°ects of prolonged suspension. Have a personal plan and practice 

it in the presence of a responsible  adult  before  leaving  the  ground.  No one escape/

rescue plan will work for every hunter, on every tree, in every circumstance. Only you 

can determine the best self-recovery/escape plan for your hunting situation before 

leaving the ground. There is time to make a correct decision on what action to take if 

a fall occurs while wearing a full-body fall arrest harness. It is important to remember, 

DO NOT PANIC. 

Remain 

calm  and  implement  your  practiced  rescue,  relief  and recovery  

plan. Hunt from the 

ground when self-recovery /escape ability is absent. Failure to follow  

these instructions 

may result in serious injury or death!

  WARNING! 

READ  THESE FULL-BODY FALL ARREST HARNESS INSTRUCTIONS 

CAREFULLY AND FOLLOW ALL THE INSTRUCTIONS! YOUR NEW FULL-BODY FALL 

ARREST HARNESS IS DESIGNED FOR A MAXIMUM CAPACITY (USER AND EQUIPMENT) 

OF 3

5

0 POUNDS (1

58

 kg). ADDITIONALLY, YOUR NEW FULL-BODY FALL ARREST 

HARNESS  MUST  BE  REPLACED  AFTER 

FIVE 

(

5

)  YEARS  OF  SERVICE!  REPLACE 

YOUR FULL-BODY FALL ARREST HARNESS IMMEDIATELY SHALL YOU EXPERIENCE 

A FALL WHILE WEARING IT.

  WARNING!

 You must use the full-body fall arrest harness provided with this product 

or a harness that complies with ASTM standards.  NOTE: You must store your full-body 
fall  arrest  harness  out  of  direct  sunlight  and  out  of  any  other  harsh  environmental 
condition(s)  that  may  adversely  a°ect  its 

performance.  Failure  to  follow  these 

instructions may result in serious injury or death!

4

Summary of Contents for 716240

























Reviews: