Form
No.
1540-69
r9/29/17 ©
2017
Bobrick
Washroom
Equipment,
Inc. Printed
in
U.S.A.
Page 14
Full Notch
Flange
58''
(147cm)
Half Notch Flange
Hinge Pin
Upper Hinge
Bracket
1-1/2''
(38mm)
55-9/16''
(141cm)
1-1/2''
(38mm)
Cam
Lower Hinge
Bracket
1/2''
(13mm)
3/8''
(9mm)
Upper
Hinge
Bracket
1-1/2''
(38mm)
12-11/16''
(32cm)
55-9/16''
(141cm)
1-1/2''
(38mm)
Cam
Lower Hinge
Bracket
1/2''
(13mm)
Headrail
Latch
Keeper &
Door Stop
Outswing
2''
(51mm)
2-3/4''
(70mm)
1-1/2''
(38mm)
3/4''
(19mm)
27-1/2''
(699mm)
Door
Latch
Keeper
Door CL
Stile CL
Stile
5/16''
(8mm)
Max.
U-Bracket
Keeper/Door
Stop
Door
Handle
Door
Stile
Door
Perpendicular
Stile
Keeper & Door Stop
Latch
Outswing
INSTALL OUTSWING DOORS
STEP 9
Fig. 9c: Perpendicular Stile
Mounting Location of Keeper.
Fig. 9a: Door-to-Stile Hardware.
Fig. 9b: Mounting
Location of Latch
and Keeper with
Emergency Access
Fig. 9d: Top View In-Line
Stile Mounting Location
of Latch and Keeper.
Overhead-Braced
Stile
Floor-Anchored
or Ceiling-Hung Stile
Outside
View
A. Secure the flanges into the door notches using
#10 x 1" (4.8 x 25mm) screws (Fig. 9a).
B. Using the hinge brackets as a template, measure and mark
the location of mounting holes in the stile. The 12-11/16"
(32cm) dimension shown (Fig. 9a Stile) is to the top edge
of the C of first hinge hole.
C. Use 1/4" (6mm) bit to drill four (4) holes through the stile.
Through-bolt the hinge brackets using one-way screws and
threaded sleeves.
D. Mount the door, then drive the hinge pin down through the
predrilled hole in the top of door.
E. Adjust the cam on the lower hinge bracket so the door
closes to desired position, then tighten the hex nut.
F. Mount latches and keepers as shown (Fig. 9b, 9d).
Through-bolt latches and keepers using one-way screws
and threaded sleeves.
NOTE: To ensure *emergency access locate the keeper
so the latch slide is seated no more than 5/16" (7mm) from
the top of the keeper. (See Fig.9b). *Emergency access
is achieved by lifting the door.
NOTE: On outswing door,
install the handle on outside of door opposite the latch
Using the door handle as a template on the outside of door,
mark location for top hole in handle 31-5/8" (803mm) up
from the bottom edge of door and 2" (50mm) from side
edge of door. Mark location for bottom hole in handle. Drill
two (2) 3/16" (5mm) diameter holes through door. Attach
door handle to outside of door using #8-32 x 1-1/4" one
way screws provided.
F
(2)
. Perpendicular Keeping Stile. Mount latch as shown (Fig.
9c). Through-bolt latch using one-way screws and threaded
sleeves.
NOTE: Using keeper as template, place keeper as shown
in (Fig. 9c) to line up with latch slide. Mark location of
mounting holes. Secure keeper to stile using #10 x 5/8"
screws.
G. Mount robe hooks to doors at locations where they can
also perform as door bumpers. NOTE: On outswing doors,
position robe hook per local barrier-free codes.
H. If required, apply a synthetic lubricant to the hinge.
I.
Clean stalls as required.
Perpendicular Stile to
Panel See Fig. 9c
Door
L
