Form
No.
1540-69
r9/29/17 ©
2017
Bobrick
Washroom
Equipment,
Inc. Printed
in
U.S.A.
Page 13
Full Notch
Flange
58''
(147cm)
Half Notch Flange
Hinge Pin
Upper Hinge
Bracket
1-1/2''
(38mm)
55-9/16''
(141cm)
1-1/2''
(38mm)
Cam
Lower Hinge
Bracket
1/2''
(13mm)
3/8''
(9mm)
Upper
Hinge
Bracket
1-1/2''
(38mm)
12-11/16''
(32cm)
55-9/16''
(141cm)
1-1/2''
(38mm)
Cam
Lower Hinge
Bracket
1/2''
(13mm)
Headrail
Latch
Keeper &
Door Stop
Inswing
1-1/2''
Door
Latch
Keeper &
Door Stop
Door CL
Panel
Panel
CL
Stile
2-1/2''
2''
Latch
Keeper &
Door Stop
Inswing
Door
Latch
Keeper
Door CL
Stile CL
Stile
5/16''
(8mm)
Max.
1-1/2''
(38mm)
2-3/4''
(70mm)
1-1/2''
(38mm)
3/4''
(19mm)
27-1/2''
(699mm)
U-Bracket
Stile
Inswing
Door
Stile
Through-Bolts
F-Bracket
Hinge
Coat Hook
Slide Latch
Keeper &
Doorstop
INSTALL INSWING DOORS
STEP 8
Fig. 8c: Perpendicular Stile
Mounting Location of Latch and Keeper.
Floor-Anchored
or Ceiling-Hung Stile
Fig. 8a: Door-to-Stile Hardware.
Fig. 8b: Mounting
Location of Latch,
Keeper with Emergency
Access
Fig. 8d: Top View InLine Stile
Mounting Location of Latch and Keeper.
Overhead-Braced
Stile
Inside
View
A. Secure the flanges into the door notches using
#10 x 1" (4.8 x 25mm) screws (Fig. 8a).
B. Using the hinge brackets as a template, measure and
mark the location of mounting holes in the stile. The
12-11/16" (32cm) dimension shown (Fig. 8a Stile) is to
the top edge of the stile to C of first hinge hole.
C. Use 1/4" (6mm) bit to drill four (4) holes through the
stile. Through-bolt the hinge brackets using one-way
screws and threaded sleeves.
D. Mount the door, then drive the hinge pin down through
the predrilled hole in the top of door.
E. Adjust the cam on the lower hinge bracket so the door
closes to desired position, tighten hex nut.
F. Mount latch and keeper as shown (Fig. 8b, 8d).
Through-bolt latch and keeper using one-way screws
and threaded sleeves.
NOTE: To ensure *emergency access locate the
keeper so the latch slide is seated no more than
5/16" (7mm) into the keeper slot as shown (Fig. 8b).
*Emergency access is achieved by lifting door.
F
(2)
. Perpendicular Keeping Stile. Mount latch as shown
(Fig. 8c). Through-bolt latch using one-way screws
and threaded sleeves. Using keeper as template,
place keeper as shown in (Fig. 8c) overhanging edge
of stile, to line up with latch slide. Mark location of
mounting holes. Secure keeper to stile using #10 x
5/8" screws.
G. Mount robe hooks to doors at locations where they
can also perform as door bumpers.
H. If required, apply a synthetic lubricant to the hinge.
I. Clean stalls as required.
L
Door
Perpendicular Stile
See Fig. 8c
