BMW Motorrad F 750 GS 2021 Rider'S Manual Download Page 55

Page: 55 / 314

Find the correct tyre pres-

sures in the following places:

Back cover of the rider's

manual

Instrument cluster in the

TYRE

PRESSURE

view

Sign under the seat

Tyre pressure outside

permitted tolerance

with tyre pressure control

(RDC)

lights up yellow.

is displayed in yellow.

Tyre pressure does
not match setpoint.

Stop immediately! Check
tyre pressure.

Tyre press. control.
Loss of pressure.

Stop immediately! Check
tyre pressure.

WARNING

Tyre pressure outside the

permitted tolerance.

Risk of accident, degradation

of the vehicle's driving char-

acteristics.

Adapt your style of riding

accordingly.

Possible cause:

Measured tyre pressure is out-

side permitted tolerance.

Check the tyre for damage

and to ascertain whether the

vehicle can be ridden with the

tyre in its present condition.

If the vehicle can be ridden

with the tyre in its present con-

dition:

Correct the tyre pressure at

the earliest possible oppor-

tunity.

Before adjusting tyre pres-

sure, read the information on

temperature compensation

and adjusting pressure in the

section entitled "Engineering

details":

Temperature compensation

(

168)

Pressure adaptation (

169)

Find the correct tyre pres-

sures in the following places:

Back cover of the rider's

manual

Instrument cluster in the

TYRE

PRESSURE

view

Sign under the seat

Have the tyre checked for

damage by a specialist work-

shop, preferably an authorised

BMW Motorrad retailer.

You can deactivate RDC

warnings for riding in off-

road mode.

Summary of Contents for F 750 GS 2021



























































































































































































































































































































Search results

Summary of Contents for F 750 GS 2021

Reviews:

Brands by name

Popular brands

BMW Motorrad F 750 GS 2021, Rider'S Manual

Search results

Summary of Contents for F 750 GS 2021

Reviews:

Brands by name

Popular brands