background image

2

defiant

A

A S

S S

S E

E M

M B

B L

L Y

Y

&

&

D

D II S

S A

A S

S S

S E

E M

M B

B L

L Y

Y

A s s e m b l y

&

D i s a s s e m b l y

GETTING STARTED

WHEN DISASSEMBLING THE DEFIANT 2 ALWAYS ENSURE THE MARKER IS DEGASSED.

The DISASSEMBLY portion of this manual will be divided into three sections.

I. Trigger Frame Disassembly

II. Regulator Disassembly

III. Body Disassembly

NOTE: When ASSEMBLING the DEFIANT 2, perform the entire disassembly
process in reverse order.

I.

TRIGGER FRAME DISASSEMBLY

1. Remove left side LED Grip.

2. Remove 4 allens to separate Trigger Frame Halves, exposing circuit board.

3. Disconnect Battery.

4. Remove 2 Board retaining screws. (1-1/16 Allen Head screw and 1-Phillips Head screw)

5. Flip Board over towards left side to expose wiring..

6. Lift up on black LCD ribbon locks located on each side of membrane ribbon harness and 

remove complete membrane assembly from trigger frame.

7. Remove Battery and Solenoid Harness.

I.

TRIGGER FRAME DISASSEMBLY

(continued)

8. Remove Eye Sensor Wire Harness.

9. Remove Circuit Board.

10. Remove Shouldered Trigger Retaining Screw and lift out Trigger and Trigger Return Spring.

11. Loosen Front Frame Retaining Screw.

12. Remove Rear Frame Retaining Screw.

13. Lift Out Front Hose from Around Hose Guard. (A small allen wrench works well)

14. Slide Trigger Frame Back from Body.

15. Remove Trigger Frame.

16. Diconnect Solenoid from Body.

NOTE: 

Use care when removing airlines.

Always inspect hoses after removal to ensure no tears or damage occurred during removal.

Flip Board To Expose Wiring

Lift Up LCD Ribbon Locks

Remove Battery/Solenoid Harness

Separate Trigger Halves

Disconnect Battery

Remove Board Retaining Screws

W A R N I N G !

Ensure Air Source is disconnected and Marker
is discharged before making any mechanical

adjustments to Marker internals or electronics.

Slide Frame Back From Body

Remove Trigger Frame

Remove Solenoid From Body

Loosen Front Frame Retaining Screw

Remove Rear Frame Retaining Screw

Lift Hose From Around Hose Guard

Remove Trigger

Remove Board

Remove Eye Harness

2

3

4

7

5

6

Grip Removal

1

8

13

16

12

15

11

14

9

10

12

11

Defiant 2 Manual ƒ  5/31/05  5:46 PM  Page 13

Summary of Contents for DEFIANT 2















Reviews: