L
Lo
oo
ok
kss c
ca
an
n k
kiillll
L
L o
o o
o k
k ss c
c a
a n
n k
k ii ll ll
W
W A
A R
R N
N II N
N G
G
IIN
NT
TR
RO
O
I n t r o d u c t i o n
2
defiant
Always ensure Marker is not shooting at a dangerous velocity. Ensure all participants
are wearing the proper Paintball safety equipment. You will be held liable if someone
is injured by a Paintball fired from your Marker regardless of fault.
WARRANTY
B.L.A.S.T. warrantees the DEFIANT 2 against damages in Manufacturing Defects only.
Electrical components are warranted for a period of 90 days. Solenoids are not warranted.
When utilizing after market Drop-Forwards ensure attachment bolts DO NOT protrude
into internal grip assembly. When utilizing aftermarket grips ensure attachment bolts
DO NOT protrude into internal grip assembly. Failure to do so may damage the internals
and will result in void of warranty. Use of Teflon tape will void warranty. Aftermarket
anodizing will result in void of warranty.
For questions concerning your
DEFIANT 2
manual please call (925) 625-7929.
OPERATION
The
DEFIANT 2
Marker is a solenoid controlled open-bolt design. The bolt is locked onto
a slotted bolt receiver that is attached to a dual pressurized machined slider (RAM),
and is controlled by the solenoid (An electronic 4-way valve control). The newly designed,
encapsulated ram sleeve features two chambers (one toward the front and one toward
the rear). The back of the chamber is pressurized to move the bolt forward, and the front
is pressurized to move the bolt backward. This allows for very low cycling pressure, as well
as much less cocking recoil.
GENERAL DESCRIPTION
The
DEFIANT 2
is a low pressure operating, open bolt, electronic Marker, featuring microchip
managed solenoid control, anti-chop eyes (ACE), dedicated low and high pressure regulators,
and unique patented pending modular ram sleeve.
The field strippable pull pin bolt is connected to a slotted bolt receiver that is attached to
a dual pressurized sliding ram. This ram is held within the encapsulated ram sleeve located
in the lower tube of the body. The low pressure regulator supplies air through the lower tube
of the body, through the valve, through the front barb, to the front barb of the solenoid. Upon
activation, the solenoid redirects alternating pressure through the rear barbs, from the
chamber in front of the ram to the back chamber behind the ram. The forward shifting ram
will then strike the poppet, opening the main valve which releases high pressure regulated
air up through the transfer port and into the upper tube of the body. The pull pin connected
bolt pushes the paintball into the breech while simultaneously redirecting the charge of air
to propel the projectile (paintball) to its target.
W a r n i n g
The DEFIANT 2 is controlled via the MEMBRANE PAD located on the rear of the Trigger Frame, as
well as the Dip Switch Control Panel located on the front side of the Frenzy Board. All of the
functions of the DEFIANT 2 can be easily accessed and changed by using both the Membrane
Pad and Dip Switch Panel.
GETTING STARTED
To power up your
DEFIANT 2
, Press the ON/OFF button. To turn off your
DEFIANT 2
, press and hold the
ON/OFF button for approximately 1 second until the LED turns Red and release. Buttons 1 and 2 allow
the user to change the Eye Sensor’s operational mode. Once powered up, pressing Button 1 will
change the Eye Sensor to Dry Fire Mode (also known as Simulation Mode), while Button 2 sets the
Eye Sensor to Delay Mode. Every
DEFIANT 2
is equipped with a 3-Color, Light Emitting Diode (LED),
located on the side grip panel (left of the membrane pad) which allows the user to verify the current
Eye Sensor Mode and/or Battery Status. A detailed description of each function can be found in the
Board Operation section.
NOTE:
The Frenzy Board IS NOT Programmable via the trigger.
TRIGGER ADJUSTMENT
The trigger is fully adjustable using the three screws within the trigger. The upper screw controls
the return spring tension, the center screw adjusts micro-switch activation point and the lower
screw adjusts the trigger stop point.
BBA
AR
RR
REEL
L
The
DEFIANT 2
comes standard with a one piece, .689 Bore, 12-inch Assassin barrel.
Barrel threads for the
DEFIANT 2
are Auto-cocker type.
SPECIFICATIONS
Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DEFIANT 2
Caliber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electro-Pneumatic
Air Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compressed Air/Nitrogen
Battery Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-Volt Battery
Cycle Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15bps Capped
and/or
Unlimited
Firing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Semi Auto
and/or
Ramping Modes
Effective Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
150+ feet
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(With 12” Assassin Barrel) 2lbs., 1oz.
Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(With 12” Assassin Barrel) 18.25 inches
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.875 inches
*Weight of Marker without 12” Assassin Barrel is 1lbs., 13oz.
4
3
*
Defiant 2 Manual ƒ 5/31/05 5:44 PM Page 5
