background image

 
 

 

BH North America Corporation •  20155 Ellipse  •  Foothill Ranch  •  CA  •  92610 

www.bladezfitness.com 

7

FOLDING THE TREADMILL 

 

CAUTION 

The cylinder is under high pressure and care 
must be taken to prevent damage to it by 
impact with other objects. If the cylinder is 
damaged, it may prevent the treadmill from 
raising or lowering smoothly and slowly.

 

 

 

 

FOLDING 

To fold your treadmill into the upright position, 
first set the elevation to 0 % incline. The 
treadmill will not lock into the upright position if 
the treadmill is not at 0 % incline. Be sure to 
turn the power off and unplug the power cord. 
Using both hands, lift the treadmill by the end 
caps at the rear of the treadmill and push it up 
until the retaining shaft locks the treadmill into 
place. 

UNFOLDING 

To unfold the treadmill from the upright 
position simply depress the unfolding pedal 
with your foot and guide the deck down with 
both hands. Make sure that you do not let go 
until the deck is firmly on the floor. Be careful 
when unfolding if children are present. 

MOVING THE TREADMILL 

The treadmill will need to be locked in the 
upright position as illustrated. 
Grasp the end caps with both hands and 
slowly pull the deck down towards your body 
until the casters are able to roll freely. Keep 
the treadmill at that angle until you are done 
with your move. 

 

Summary of Contents for 9.9T















































Reviews: