background image

28

EN

Compliance Information for the European Union

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it 
is the user’s responsibility to dispose of their waste equipment by 
handing it over to a designated collections point for the recycling of 
waste electrical and electronic equipment. The separate collection and 
recycling of your waste equipment at the time of disposal will help 
to conserve natural resources and make sure that it is recycled in a 
manner that protects human health and the environment. For more 

information about where you can drop off your waste equipment for recycling, please 
contact your local city offi ce, your household waste disposal service or where you 
purchased the product.

EU Compliance Statement:

RTF:

Horizon Hobby, LLC  hereby declares that 
this product is in compliance with the 
essential requirements and other relevant 
provisions of the R&TTE, RED, and EMC 
Directives.

BNF:

Horizon Hobby, LLC  hereby declares that 
this product is in compliance with the 
essential requirements and other relevant 
provisions of the RED and EMC Directives.

A copy of the EU Declaration of Conformity is available online at:
 http://www.horizonhobby.com/content/support-render-compliance.

Summary of Contents for Blade mSR S






























Reviews: