Black+Decker BDINF12 Instruction Manual Download Page 5

Page: 5 / 22

English

will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. The
following table shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use
the next heavier gauge. The smaller the gauge number,
the heavier the cord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

120V

0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

Ampere Rating

More Not more

American Wire Gauge

Than Than

0 - 6

6 - 10

•

OUTDOOR USE EXTENSION CORDS.

When tool is

used outdoors, use only extension cords intended for use
outdoors and so marked.

•

STAY ALERT.

Watch what you are doing.Use common

sense.Do not operate tool when you are tired.

•

CHECK DAMAGED PARTS.

Before further use of the

tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting, and any other conditions that may
affect its operation. A guard or other part that is damaged
should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this
instruction manual. Have defective switches replaced by
authorized service center. Do not use tool if switch does
not turn it on and off.

•

DO NOT OPERATE

portable electric tools near flammable

liquids or in gaseous or explosive atmospheres. Motors in
these tools normally spark, and the sparks might ignite fumes.

ADDITIONAL SAFETY WARNINGS FOR YOUR
INFLATOR

WARNING:

FOR HOME AND CAR USE ONLY:

• Inflate bike tires, balls, rafts, swimming pool floats,

air mattresses, and more in and around the home.
Recommended maximum continuous duty at 65 psi is 2
minutes on with 5 minutes off.

WARNING: RISK TO BREATHING.

• The compressed air from your inflator is not safe for

breathing. Never inhale air from your inflator or from a
breathing device connected to the inflator.

WARNING: RISK OF BURSTING.

• Too much air pressure causes a hazardous risk of bursting.

Check the manufacturer’s maximum pressure rating for
objects being inflated.

• Do not leave inflator running unattended. It could burst

tires or other items.

• Use a tire gauge to check the tires pressure before each use

and while inflating tires; see the tire sidewall for the correct
tire pressure.

WARNING: RISK OF UNSAFE OPERATION.

• Do not modify or attempt to repair. Never drill into,

weld, or make any modifications to the inflator or its
attachments.

• Operate only with the accessories included or air handling

parts acceptable for not less than 160 psi. The use of any
accessory not recommended for use with this tool could
be hazardous.

• Never “horseplay.” High pressure air is dangerous. Don’t

direct air-flow at yourself or others.

WARNING:

Always leave the valve adaptor lever open

when not in use.

WARNING: RISK OF FIRE:

• Inflator can become hot during use. Allow inflator to cool

30 minutes before storing away.

CALIFORNIA PROPOSITION 65

WARNING:

This product or its power cord contains

lead, a chemical known to the State of California to
cause cancer and birth defects or other reproductive
harm. Wash hands after handling

LIQUID CRYSTAL DISPLAY FLUID
(FIRST AID MEASURES)

if liquid crystal comes in contact with your skin:

• Wash area off completely with plenty of water. Remove

contaminated clothing.

if liquid crystal gets into your eye:

• Flush the affected eye with clean water and then seek

medical attention.

if liquid crystal is swallowed:

• Flush your mouth thoroughly with water. Drink large

quantities of water and induce vomiting. Then seek
medical attention.

The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ......................... volts
Hz .......................hertz
min .....................minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute
BPM ....................beats per minute
IPM .....................impacts per minute
RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM ....................strokes per minute
A .........................amperes
W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

no .......................no load speed

n .........................rated speed