manualshive.com logo in svg

Black Box LRU4240, User Manual

The Black Box LRU4240 User Manual is the ultimate guide to maximize productivity and usage of your LRU4240 device. Easily downloadable for free from manualshive.com, this comprehensive manual provides step-by-step instructions and valuable insights to ensure seamless operation and optimal performance of your Black Box LRU4240.

Share
Download
background image

162

SALES: 0870 90 10 750

Dual Trunk E1 Router User’s Guide

Dual Trunk E1 Router

Related Commands

area default-cost, area stub, ip ospf authentication-key

area default-cost

Use the area default-cost command to specify a cost for the default summary route sent into a stub.
Use the no form of this command to remove the assigned default-route cost.

Command Syntax

   area AREAID default-cost <0-16777215>
no area AREAID default-cost
AREAID=A.B.C.D|<0-4294967295>
A.B.C.D= The IPv4 specification of the address for the stub.
AREAADDRESSID= The area identification number for the stub.
default-cost Indicates the cost for the default summary route used for a stub. Default value of cost is 1.

Command Mode:

 Router mode

Usage

Area command has two configuration options, stub and default-cost. The default-cost option provides the metric for the summary 
default route, generated by the area border router, into the stub area. Use this option only on an area border router that is attached 
to the stub area. Refer to RFC 1587 for information on stub area.

Examples

This example sets the default-cost to 10 for area 1.
ospfd# configure terminal
ospfd(config)# router ospf 100
ospfd(config-router)# area 1 default-cost 10

Related Commands

area authentication, area stub

area export-list

Use the area export-list command to define restrictions on routes that are advertised from a specified area.
Use the no form of this command to disable this function.

Command Syntax

   area AREAID export-list NAME
no area AREAID export-list
AREAID=A.B.C.D|<0-4294967295>
A.B.C.D= The IPv4 specification of the address for the stub.
<0-4294967295>= The area identification number for the stub.
NAME The name of the configured access list.

Command Mode: 

Router mode

Usage

Use the export-list in combination with the access list to specify the routes that will be advertised to other areas.This command is 
applied only when generating summary-LSAs (type 3).

Examples

ospfd# configure terminal
ospfd(config)# access-list list1 deny 172.22.0.0/8
ospfd(config-router)# area 1 export-list list1

Related Commands

access list

area import-list

Use the area import-list command to import summary routes from a stub.
Use the no form of this command to disable this function.

Command Syntax

   area AREAID import-list NAME
no area AREAID import-list

Summary of Contents for LRU4240



























































































































































































































Reviews:

No comments

Related manuals for LRU4240

Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
VCS VideoJet 100 Manual preview
VideoJet 100
Brand: VCS Pages: 118
Paradyne Hotwire ATM Line Cards 8335 User Manual preview
Hotwire ATM Line Cards 8335
Brand: Paradyne Pages: 132
FOR-A MFR-1616 Quick Start Manual preview
MFR-1616
Brand: FOR-A Pages: 2
Ubiquiti EdgeRouter ER-8 Quick Start Manual preview
EdgeRouter ER-8
Brand: Ubiquiti Pages: 20
Cyclades AlterPath Manager 2500 Installation, Configuration And User Manual preview
AlterPath Manager 2500
Brand: Cyclades Pages: 368
Wave wifi MBR Series Quick Start Manual preview
MBR Series
Brand: Wave wifi Pages: 3
Lanner NCA-6520 User Manual preview
NCA-6520
Brand: Lanner Pages: 141
Amphenol C2LINX Series Installation Manual preview
C2LINX Series
Brand: Amphenol Pages: 43
Alcatel 7270 MSC Specifications preview
7270 MSC
Brand: Alcatel Pages: 4
ActionTec MI424WR MI424WR Upgrade Procedure preview
MI424WR
Brand: ActionTec MI424WR Pages: 3
Erbauer 3663602796282 Original Instructions Manual preview
3663602796282
Brand: Erbauer Pages: 36
M-Audio FireWire 1814 Manual Del Usuario preview
FireWire 1814
Brand: M-Audio Pages: 67
ZyXEL Communications WAP6804 User Manual preview
WAP6804
Brand: ZyXEL Communications Pages: 114
Lancom 1711+ VPN Manual preview
1711+ VPN
Brand: Lancom Pages: 79
Supero AOC-SIMLP-3+ User Manual preview
AOC-SIMLP-3+
Brand: Supero Pages: 66
New Media Technology IP Power 9212 User Manual preview
IP Power 9212
Brand: New Media Technology Pages: 26
ADF Web AXIS HD67555 User Manual preview
AXIS HD67555
Brand: ADF Web Pages: 20

Brands by name

Popular brands

Load more brands