Black Box LRU4240 User Manual Download Page 93 | Manualshive

Page: 93 / 218

background image

Dual Trunk E1 Router

Dual Trunk E1 Router User’s Guide

TECHNICAL: 0118 96 56 000

81

In-band Network Registers, 24 Hour Detail

On an in-band enabled system, Menu-3CB shows the performance data which describes l

RMON-2

RMON-2 provides additional SNMP reporting capabilities and the ability to identify the top
bandwidth users.

When using RMON-2 with the Dual Trunk E1 Router, the following RMON-2 groups are available:

• Protocol Directory
• Protocol Distribution
• Network Layer Host Table
• Application Layer Host Table
• Network Layer Matrix Table
• Application Layer Matrix Table

Protocol Directory

The RMON-2 Protocol Directory lists the protocols that the Dual Trunk E1 Router (agent) is
monitoring on the network. The Dual Trunk E1 Router is capable of monitoring up to 16 protocols
at a time. The default configuration includes the following protocols:

• IP
• ICMP
• UDP
• TCP
• FTP Control
• FTP Data
• Telnet
• SMTP (e-mail)
• DNS
• HTTP
• NETBIOS Name Service
• NETBIOS Datagram Service
• NETBIOS Session Service
• SNMP

Table 9-4

Menu-3CB Field Definitions

Field

Definition

CRC

Number of packets received with CRC errors per interval.

RxPkt

Number of received packets per interval.

Rx%

Bandwidth utilization in the received direction per interval.

TxPkt

Number of packets sent out per interval.

Tx%

Bandwidth utilization in the transmit direction during interval.

«
...
91
92
93
94
95
...
»

Summary of Contents for LRU4240



























































































































































































































Reviews:

No comments

Related manuals for LRU4240

SR8800 IM-FW-II

Brand: H3C Pages: 107

Brand: 3Com Pages: 12

Brand: H3C Pages: 16

H3C S3600 Series

Brand: H3C Pages: 10

Brand: H3C Pages: 42

Brand: H3C Pages: 2

H3C S7500E Series

Brand: H3C Pages: 34

Brand: H3C Pages: 33

Brand: H3C Pages: 14

Brand: H3C Pages: 56

H3C S7500E Series

Brand: H3C Pages: 112

Brand: H3C Pages: 15

SR8800 IM-FW-II

Brand: H3C Pages: 5

H3C S7500E Series

Brand: H3C Pages: 50

Brand: H3C Pages: 37

Brand: H3C Pages: 4

Brand: H3C Pages: 5

Brand: H3C Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands