manualshive.com logo in svg

Black Box LRU4240, User Manual

The Black Box LRU4240 User Manual is the ultimate guide to maximize productivity and usage of your LRU4240 device. Easily downloadable for free from manualshive.com, this comprehensive manual provides step-by-step instructions and valuable insights to ensure seamless operation and optimal performance of your Black Box LRU4240.

Share
Download
background image

Dual Trunk E1 Router

Dual Trunk E1 Router User’s Guide

TECHNICAL:  0118 931 2233 

117

DDR Threshold 

Set this threshold between 0% and 100%. 0% means that this feature is disabled. 
Configurable to one thousandth of a percent (for example, 99.999%). When the DDR 
falls below this threshold:

• An event is sent to the Event Log

• A trap will be sent to the NMS (if configured)

• An alarm message will be displayed on the Terminal User Interface

• A DDR threshold violation is counted0%

Default: 

0%

Delay Period 

Set the Delay Period between 1 minute and 255 minutes. This figure represents the 
time interval between delay measurements on each PVC.

Default: 

1

Delay Packet Size

Set the Delay Packet Size between 50 bytes and 1500 bytes. This figure represents the 
size of Request and REsponse packets used to measure delay.

Default: 

128

Table D-8 Main-1 Status

Parameter

Description

Unit status

Indicates the 

Dual Trunk E1 Router

 is operating normally, or if any special 

conditions exist.

Network status

Displays information on the condition of the received T1 or E1 signal.

Ethernet status

Indicates if the Ethernet link is up or down.

Link1/Link 2 status

Indicates the status, up or down,  of the network link 1(NET1)  and network 
link 2 (NET2).

Table D-9 Menu-1 Unit Status

 (1 of 2)

Indication

Description

Normal

No abnormal conditions exist.

Self Test

Unit is running self test.

Net Lpbk (port)

Unit is in network loopback.

PLD Lpbk (port, fraction)

Unit is in payload loopback.

Send User 1 (port, fraction)
 port = Net1 or Net2

Unit is sending User 1 pattern.

Send User 2 (port, fraction)

Unit is sending User 2 pattern.

Send 1:1 (port, fraction)

Unit is sending alternate 1s and 0s.

Send 1:2 (port, fraction)

Unit is sending standard loopdown remote code continuously.

Send 1:4 (port, fraction)

Unit is sending standard loopup remote code continuously.

Send 1:7 (port, fraction)

Unit is sending 1:7 pattern.

Send 3:24 (port, fraction)

Unit is sending 3:24 pattern.

Table D-7 Menu-0H SLA Configuration

Parameter

Description

Summary of Contents for LRU4240



























































































































































































































Reviews:

No comments

Related manuals for LRU4240

Paradyne COMSPHERE 3800 Series Release Note preview
COMSPHERE 3800 Series
Brand: Paradyne Pages: 88
Paradyne COMSPHERE 3800PLUS Supplementary Manual preview
COMSPHERE 3800PLUS
Brand: Paradyne Pages: 5
Paradyne Hotwire 6212 Quick Installation Instructions preview
Hotwire 6212
Brand: Paradyne Pages: 2
Qlogic SANbox 6142 Supplementary Manual preview
SANbox 6142
Brand: Qlogic Pages: 2
Qlogic iSR6142 User Manual preview
iSR6142
Brand: Qlogic Pages: 172
FS FS-BOX-V3 Quick Start Manual preview
FS-BOX-V3
Brand: FS Pages: 19
Rosewill RC-402 User Manual preview
RC-402
Brand: Rosewill Pages: 3
Nexxt NOVA300 AML02304U1 User Manual preview
NOVA300 AML02304U1
Brand: Nexxt Pages: 75
Nilox 16NX071900001 User Manual preview
16NX071900001
Brand: Nilox Pages: 66
Solwise 3GWIFIMRD User Manual preview
3GWIFIMRD
Brand: Solwise Pages: 231
Cyclades AlterPath Manager 2500 Installation, Configuration And User Manual preview
AlterPath Manager 2500
Brand: Cyclades Pages: 368
SONIX MP5S Plus Writer Quick Manual preview
MP5S Plus Writer
Brand: SONIX Pages: 23
Alvarion BreezeNET DS.11 Configuration Utility Release Note preview
BreezeNET DS.11 Configuration Utility
Brand: Alvarion Pages: 2
Beck com.tom INDUSTRY 100.WLAN.W Startup Manual preview
com.tom INDUSTRY 100.WLAN.W
Brand: Beck Pages: 2
LanReady AP-952X User Manual preview
AP-952X
Brand: LanReady Pages: 40
Xtatix XCA-PDSI User Manual preview
XCA-PDSI
Brand: Xtatix Pages: 12
Hamlet HRDSL108W Quick Installation Manual preview
HRDSL108W
Brand: Hamlet Pages: 6
H3C MSR 2600 Installation, Quick Start preview
MSR 2600
Brand: H3C Pages: 4

Brands by name

Popular brands

Load more brands