Black Box LRU4240 User Manual Download Page 169 | Manualshive

Page: 169 / 218

background image

Dual Trunk E1 Router

Dual Trunk E1 Router User’s Guide

TECHNICAL: 0118 96 56 000

157

Use the

ip rip send

packet command to configure the interface to enable the sending of RIP packets. This feature allows the user

to control the sending of packets directly on the specified interface. Therefore, the packet sending is more efficient and
controllable.

Command Syntax

ip rip send-packet
no ip rip send-packet

Command Mode:

interface

Examples

ip rip send-packet

ip rip send version

Use the

ip rip send version

command to send RIP packets on an interface using version control.

Use the

no

option on this command to use the global RIP version control rules.

Command Syntax

ip rip send version 1|2|[1 2]
no ip rip send version (1|2)
1 - specifies sending of RIP version 1 packets out of an interface.
2 - specifies sending of RIP version 2 packets out of an interface.
1 2- permits sending of both RIP version 1and 2 packets out of an interface.

Command Mode:

Router Configuration

Examples
ip rip send version 1

ip rip send version 1-compatible

Use the ip rip send version 1-compatible

command to send RIP version 1 compatible packets from a version 2 RIP interface to

other RIP interfaces. This mechanism causes version 2 RIP to broadcast the packets instead of multicasting them.
Use the

no

option on this command to use the global RIP version control rules.

Command Syntax

ip rip send version 1-compatible

Command Mode:

Router Configuration

Examples

ip rip send version 1-compatible

Usage

Notes

For testing this case, the configuration must be:!
interface XXXX
ip rip send version 1-compatible
!
router rip
version 2

NOTE:

The default version for ripd is version 2. Use the

version

command to explicitly specify a different version.

ip split-horizon

Use the

ip split-horizon

command to perform the split-horizon action on the interface. The default is

split-horizon

poisoned

.

Use the

no

option on this command to disable this function.

Command Syntax

ip split-horizon (poisoned)

poisoned

perform split-horizon with poisoned reverse.

no ip split-horizon

Command Mode:

Router Configuration

Examples

ip split-horizon

«
...
167
168
169
170
171
...
»

Summary of Contents for LRU4240



























































































































































































































Reviews:

No comments

Related manuals for LRU4240

Brand: D-Link Pages: 176

Brand: ?omtime Pages: 62

Brand: Black Box Pages: 9

Brand: TRENDnet Pages: 2

Brand: Paradyne Pages: 6

ReadyNAS 3220 Series

Brand: NETGEAR Pages: 4

24-Port 1000BASE-T

Brand: Comet Labs Pages: 44

Brand: Goobay Pages: 20

Brand: Vivotek Pages: 317

Brand: IBM Pages: 168

Brand: Clas Ohlson Pages: 4

Brand: Patton electronics Pages: 40

Brand: l-com Pages: 11

Brand: TP-Link Pages: 182

Brand: U-Media Pages: 42

Brand: MSE Pages: 35

Brand: Atlantis Land Pages: 85

EIR508-2-T Series

Brand: B&B Electronics Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands