Black Box LRU4240 User Manual Download Page 168 | Manualshive

Page: 168 / 218

background image

156

SALES: 0870 90 10 750

Dual Trunk E1 Router User’s Guide

Dual Trunk E1 Router

send

- specifies that information for sent packets be displayed.

no debug rip (events | packet | zebos)

Command Mode:

: Enable

Examples

RIP(enable)#debug rip events
7: RECV packet from 60.10.2.1 port 520 on net2
8: update timer fire!
9: SEND UPDATE to net2 ifindex 4
10: unicast announce to 60.10.2.1 on net2
11: update routes to neighbor 60.10.2.1
12: SEND to socket 34 port 520 addr 60.10.2.

distance

Use the

distance

command to set the administrative distance.

Use the

no

form of the command to disable this function.

Command Syntax
(no) distance

DISTANCE (A.B.C.D/M (ACCESSLIST))

DISTANCE

=<1-255>

Specifies the administrative distance value.

A.B.C.D(/M)

Specifies the network prefix and length.

ACCESSLIST

Specifies the access-list name.

Command Mode:

: Router Configuration

Examples
distance

8 10.0.0.0/8 mylist

no distance

9

ip rip receive-packet

Use the

ip rip receive

packet command to configure the interface to enable the reception of RIP packets. This feature allows the

user to control the receiving of packets directly on the specified interface. Therefore, the packet receiving is more efficient and
controllable.

Command Syntax

ip rip receive-packet
no ip rip receive-packet

Command Mode:

: interface

Examples

ip rip receive-packet

ip rip receive version

Use the

ip rip receive version

command to receive specified version of RIP packets on an interface basis using version control,

and override the setting of the version command.
Use the no form of this command to use the setting established by the version command.

Command Syntax
ip rip receive version

1|2|[1 2]

no ip rip receive version

(1|2|[1 2])

1

- specifies acceptance of RIP version 1 packets on the interface.

2

- specifies acceptance of RIP version 2 packets on the interface.

1 2

- specifies acceptance of RIP version 1 and version 2 packets on the interface.

Command Mode:

Router Configuration

Examples

ip rip receive version

1 2

Related Commands
version

ip rip send-packet

«
...
166
167
168
169
170
...
»

Summary of Contents for LRU4240



























































































































































































































Reviews:

No comments

Related manuals for LRU4240

Brand: Paradyne Pages: 22

Brand: C&H Technologies Pages: 46

FrameSaver 9120

Brand: Paradyne Pages: 2

Brand: Vanguard Pages: 4

Brand: ?omtime Pages: 62

Nighthawk M6 Pro

Brand: AT&T Pages: 2

Brand: Belkin Pages: 72

Brand: Helmholz Pages: 28

Brand: XNET Pages: 17

Brand: H3C Pages: 3

SmartMesh IA-510 D2511

Brand: Dust Networks Pages: 30

Brand: Draytek Pages: 2

Brand: Genie Pages: 6

InnoMedia MTA 3328-2R

Brand: VoiceLine Pages: 18

3C8567 - SuperStack II NETBuilder SI 567...

Brand: 3Com Pages: 6

Brand: IMC Networks Pages: 36

Brand: Idis Pages: 18

BiPAC 5200S RC Series

Brand: Billion Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands