Black Box LRU4240 User Manual Download Page 172 | Manualshive

Page: 172 / 218

background image

160

SALES: 0870 90 10 750

Dual Trunk E1 Router User’s Guide

Dual Trunk E1 Router

show running-config

Use the

show running-config

command to show running config.

Command Syntax

show running-config

Command Mode:

rip

There are no arguments or keywords for this command.

Examples

Rip(enable)#show running-config
2:
3: Current configuration:
4: !
5: hostname router
6: password zebos
7: enable password zebos
8: !
9: interface e0
10: !
11: interface mlppp
12: !
13: interface net1
14: !
15: interface net2
16: !
17: router rip
18:  redistribute connected
19:  network net1
20:  network net2
21: !
22: line vty
23:  no login
24: !
25: end
Rip(enable)#

show ip rip

Use the

show ip rip

command to show RIP routes.

Command Syntax

show ip rip

Command Mode:

Enable

There are no arguments or keywords for this command.

Examples

show ip rip

RIP(enable)#show ip rip
104: Codes: R - RIP, C - connected, O - OSPF, B - BGP
105:
106:   Network          Next Hop         Metric From            Time
107: R 60.10.1.0/24       60.10.2.1            2 60.10.2.1      42:45
108: R 60.10.1.2/32       60.10.2.1            2 60.10.2.1      42:45
109: C 60.10.2.0/24                             1
110: R  60.10.4.0/24      60.10.2.1             2 60.10.2.1       42:45
111: R  60.10.4.2/32      60.10.2.1            2 60.10.2.1      42:45
112: R  60.10.5.0/24      60.10.2.1             2 60.10.2.1       42:45
113: R  172.18.0.0/16      60.10.2.1             2 60.10.2.1       42:45
114: C  172.18.65.0/24                         1

timers

Use the

timers

command to adjust routing network timers.

Use the

no

form of the command to restore the defaults.

Command Syntax

timers basic TABLETIMER INFORMATIONTIMER GARBAGETIMER
no timers basic

TABLETIMER=<0-4294967295>

Specifies the routing table update timer in seconds. The default is 30 seconds.

INFORMATIONTIMER=<0-4294967295>

Specifies the routing information timeout timer in seconds. The default is

180 seconds. After this interval has elapsed and no updates for a route are received, the route is declared invalid.

«
...
170
171
172
173
174
...
»

Summary of Contents for LRU4240



























































































































































































































Reviews:

No comments

Related manuals for LRU4240

Brand: Sagem Pages: 19

Brand: B+B SmartWorx Pages: 4

Brand: BSS Audio Pages: 20

Brand: Genie Pages: 15

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

ControlPoint 2000

Brand: 4Home Pages: 20

Brand: Moxa Technologies Pages: 2

Brand: CyberTAN Pages: 67

Brand: B&B Electronics Pages: 2

SRA311-008P8 Series

Brand: Divio Pages: 4

Brand: ZyXEL Communications Pages: 170

Brand: Cabletron Systems Pages: 56

Gen3 Ethernet Module

Brand: NCD Pages: 18

Brand: 3Com Pages: 63

Brand: Martin Pages: 41

IE-SW-AL18M-16TX-2GC

Brand: Weidmüller Pages: 2

Brand: NetComm Wireless Pages: 154

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands