manualshive.com logo in svg

Black Box DESKTOP TELCO, User Manual, Page: 35 / 66

Share
Download
Black Box DESKTOP TELCO User Manual Download Page 35

TELCOLINK DT - AccessDSL NTU     

User

 

Manual

  

 

Version: 2.5 

 

Page 35 of 66 

7.2.9.5  TLM Command 

SYNTAX: TLM or T 
 
This command displays table of repeaters’ external alarm inputs. 
 

CO_FMM>TLM 
Distance Ext. Alarm Status 
---------------------------- 
REPTR | ALM1 | ALM2 | ALM3 | 
---------------------------- 
REPT 1| off  | det  |  on  | 
REPT 2|  -   |  -   |  -   | 
REPT 3|  -   |  -   |  -   | 
REPT 4|  -   |  -   |  -   | 
REPT 5|  -   |  -   |  -   | 
REPT 6|  -   |  -   |  -   | 
REPT 7|  -   |  -   |  -   | 
REPT 8|  -   |  -   |  -   | 
REPT 9|  -   |  -   |  -   | 
REPT10|  -   |  -   |  -   | 
REPT11|  -   |  -   |  -   | 
REPT12|  -   |  -   |  -   | 
REPT13|  -   |  -   |  -   | 
REPT14|  -   |  -   |  -   | 
---------------------------- 
CO_FMM> 

 

Definitions: 

Off 

– no external alarm detected 

On 

– external alarm is active  

Det 

– external alarm have been detected since last clearing of external alarm table 

 

7.2.9.6  RESETTLM Command 

SYNTAX: RESETTLM or RT 
 
This command clears the external alarm table. 

7.2.9.7  TLMCONF Command 

SYNTAX: TLMCONF or TC 
This command displays the external alarm config table. 

 

Summary of Contents for DESKTOP TELCO



































































Reviews:

No comments