manualshive.com logo in svg

Black Box DESKTOP TELCO, User Manual

Share
Download
Black Box DESKTOP TELCO User Manual Download Page 32

TELCOLINK DT - AccessDSL NTU     

User

 

Manual

  

 

Version: 2.5 

 

Page 32 of 66 

7.2.9  Fault and maintenance management FMM 

Fault and maintenance management activated 
Enter <M> to return to MAIN, or <H> for HELP information 

 

Type <H>and the monitor lists all available commands in the fault and maintenance sub-menu. 

7.2.9.1  SQ Command 

The SQ command allows the user to toggle the signal quality trace on and off: 

 
CO_01_FMM> SQ 
signal quality trace on 
xDSL SNR: local 38.8 dB, remote 39.0 dB 
xDSL SNR: local 41.3 dB, remote 38.8 dB 
xDSL SNR: local 38.6 dB, remote 39.0 dB 
 
CO_01_FMM> SQ 
signal quality trace off 
CO_01_FMM>  

Note: Units in Multipoint and Dual Pair modes represent data for both xDSL interfaces. 

7.2.9.2  STARTUP Command 

SYNTAX: STARTUP or SUP 
 
The STARTUP command allows the user to toggle the startup trace on and off, in order to observe 
the LTU / NTU activation state diagram transitions conforming to ITU-T G.991.2. 

 
CO_FMM> STARTUP 
xDSL transceiver startup trace on 
CO_FMM> 
CO_FMM> STARTUP 
xDSL transceiver startup trace off 
CO_FMM> 
 

Note: Units in Multipoint and Dual Pair modes represent data for both xDSL interfaces. 
 

Summary of Contents for DESKTOP TELCO



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands