Black Box CertiFiber TS655A Manual Download Page 63

Page: 63 / 67

Warnings and Disclaimers

No part of this document may be photocopied,

reproduced, or translated into another

language without prior written consent.

The manufacturer and its authorized agents

make no warranty of any kind with regard to

this material, including, but not limited to, the

implied warranties of merchantability and

fitness for a particular purpose. Neither the

manufacturer nor its authorized agents shall be

liable for errors contained herein or for

incidental consequential damages in

connection with the fumishing, performance,

or use of this material.

Warning: This manual and the software

described herein are protected by United

States Copyright law (Title 17 United States

code). Unauthorized reproduction and/or sales

may result in imprisonment for up to one year

and fines of up to $10,000 (l 7 USC 506).

liability.

The information in this document and the

software is subject to change without notice.

Trademarks Used in This Manual

ScanLink is a registered trademark, and

CertiFiber is a trademark, of Microtest, Inc.

Any other trademarks mentioned in this manual are
acknowledged to be the property of the trademark
owners.

CERTIFIBER™

Summary of Contents for CertiFiber TS655A



































































Search results

Summary of Contents for CertiFiber TS655A

Reviews:

Related manuals for CertiFiber TS655A

Brands by name

Popular brands

Black Box CertiFiber TS655A, Manual

Search results

Summary of Contents for CertiFiber TS655A

Reviews:

Related manuals for CertiFiber TS655A

Brands by name

Popular brands