ENGLISH • 17
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean.
Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This
will ensure that the safety of the power tool is maintained.
6. Electrical safety
La herramienta lleva un doble aislamiento; por lo
tanto no requiere una toma a tierra. Compruebe
siempre que la tensión de la red corresponda al
valor indicado en la placa de características.
Warning!
If the power cord is damaged, it must be
replaced by the manufacturer, authorized
Black & Decker Service Center or an equally
qualified person in order to avoid damage or injury.
If the power cord is replaced by an equally qualified
person, but not authorized by Black & Decker, the
warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Safety warnings common for grinding, sanding, wire
brushing or abrasive
a. This power tool is intended to function as a grinder,
wire brush, sander or cut-off tool . Read all safety
warnings, instructions, illustrations and specifications
provided with this power tool.
Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury. Operations such as polishing
are not recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
b. Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
c. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Accessories running faster than their rated speed
can break and fly apart.
d. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories cannot
be adequately guarded or controlled.
e. The arbor size of wheels, flanges, backing pads or
any other accessory must properly fit the spindle of
the power tool.
Accessories with arbor holes that do
not match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may cause
loss of control.
f. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheel for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of the
rotating accessory and run the power tool at maximum
no-load speed for one minute.
Damaged accessories
will normally break apart during this test time.
g. Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and work shop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask
or respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
h. Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece
or of a broken accessory may fly away and cause injury
beyond immediate area of operation.
i. Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord.
Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live”
and shock the operator.
SAFETy INSTRUCTIONS
FOR ALL OPERATIONS
Read
Instructions
Manual
Use
Eye
Protection
Use
Ear
Protection
V ........ Volts
A ........ Amperes
Hz .......Hertz
W ........Watts
min ..... minutes
.... Alternating
Current
.... Direct
Current
n
0
....... No-Load
Speed
.... Class II
Construction
.... Earthing
Terminal
.... Safety
Alert
Symbol
.../min.. Revolutions or
Reciprocation
per minute
