Black & Decker 1, User Manual

Page: 11 / 11

21 20
11. Put back and secure the hairpin retaining wires.
12. Connect the bulb power wire to the red power wire.
13. Tighten the retaining screw on the flange.
14. Place the reflector in position in the body of the spotlight.
15. Replace the rubber “O” ring in the groove around the perimeter of the reflector.
16. Replace glass and retaining ring so the screw holes are aligned.
17. Secure retaining ring with two screws.
18. Replace rubber bezel.
19. Operate switch to ensure proper operation of spotlight.
W WA AR RN NIIN NG G
T To o rre ed du ucce e tth he e rriissk k o off e elle eccttrriicc ssh ho occk k,, rre ep plla acce e b bu ullb b w wiitth h 6 6 vvo olltt H H3 3 5 55 5 w wa atttt
o on nllyy..
B Ba atttte erryy R Re ep plla acce em me en ntt//D Diissp po ossa all
B Ba atttte erryy R Re ep plla acce em me en ntt
The battery should last the service life of the unit. Contact your Service Center for any
information you may need.
S Sa affe e B Ba atttte erryy D Diissp po ossa all
Contains a maintenance-free, sealed, non-spillable, lead acid battery,
which must be disposed of properly. Recycling is required, contact your
local authority for information. Failure to comply with local, state and
federal regulations can result in fines, or imprisonment.
W WA AR RN NIIN NG GS S
• • D Do o n no ott d diissp po osse e o off tth he e b ba atttte erryy iin n ffiirre e a ass tth hiiss m ma ayy rre essu ulltt iin n a an n
e exxp pllo ossiio on n..
• • B Be effo orre e d diissp po ossiin ng g o off tth he e b ba atttte erryy,, p prro otte ecctt e exxp po osse ed d tte errm miin na allss w wiitth h h he ea avvyy--
d du uttyy e elle eccttrriicca all tta ap pe e tto o p prre evve en ntt ssh ho orrttiin ng g ((ssh ho orrttiin ng g cca an n rre essu ulltt iin n iin njju urryy
o orr ffiirre e))..
• • D Do o n no ott e exxp po osse e b ba atttte erryy tto o ffiirre e o orr iin ntte en nsse e h he ea att a ass iitt m ma ayy e exxp pllo od de e..
1 12 2 V Vo olltt D DC C C Ch ha arrg giin ng g A Ad da ap ptte err P Pllu ug g F Fu usse e R Re ep plla acce em me en ntt
The fuse in the plug end of the 12 Volt DC Charging Adapter protects the adapter’s
charging circuit. If the Wall Cube Charger (AC) operates, but the DC charging
adapter does not, then this fuse may be opened (blown).
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 0.5 amp/250 volt fuse.
5. Replace the fuse, spring, contact and end cap
6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12 Volt DC Charging Adapter.
TROUBLESHOOTING
N No o B Ba atttte erryy S Stta attu uss IIn nd diicca atto orr LLE ED Dss LLiig gh htt W Wh he en n C Ch ha arrg giin ng g
1. Check connection to the Wall Cube Charger (AC) or 12 Volt DC Charging Port.
2. Check connection to AC or DC power source.
3. Confirm there is a functioning AC or DC current.
U Un niitt W Wiillll N No ott O Op pe erra atte e
1. The Spotlight will not operate when charging. Be sure all adapters are
disconnected before Spotlight use.
2. If you suspect the bulb is blown, check the filament. If the filament is coiled and
unbroken, the bulb is not blown. If bulb is blown, replace it.
3. The battery may be completely discharged. Charge the unit following the
directions on this manual.
4. If the Spotlight does not operate after recharging as directed, contact your
Service Cente.
S Sp pe ecciiffii cca attiio on nss
VEC156BD AR B3 B2C BR
Voltage 220V 120V 220V 127V/220V
Frequency 50Hz 60Hz 50Hz 60Hz
DC Plug Fuse 0.5 A/250V 0.5 A/250V 0.5 A/250V 0.5 A/250V
AC Charger 15V (200mA) 12V (300mA) 12V (300mA) 15V (300mA)